background image

Introduction

CONGRATULATIONS

on the purchase of your

Exmark equipment. This product has been carefully
designed and manufactured to give you a maximum
amount of dependability and years of trouble-free
operation.

This manual contains operating, maintenance,
adjustment, and safety instructions for your Exmark
equipment.

BEFORE OPERATING YOUR EQUIPMENT,
CAREFULLY READ THIS MANUAL IN ITS
ENTIRETY.

By following the operating, maintenance, and
safety instructions, you will prolong the life of your
equipment, maintain its maximum efficiency, and
promote safe operation.

Important:

To maximize safety, performance,

and proper operation of this machine, it is
essential that all operators carefully read and
fully understand the contents of the Operator’s
manual provided with the product. Safe
operation of Exmark equipment is essential.
Failure to comply with the operating instructions
or receive proper training may result in injury.
Go to http://www.Exmark.com for additional
safe operation information, such as safety tips,
training materials, and Operator’s manuals.

If additional information is needed, or should
you require trained mechanic service, contact your
authorized Exmark equipment dealer or distributor.

All Exmark equipment dealers and distributors are
kept informed of the latest methods of servicing
and are equipped to provide prompt and efficient
service in the field or at their service stations. They
carry ample stock of service parts or can secure them
promptly for you from the factory.

All Exmark parts are thoroughly tested and inspected
before leaving the factory, however, attention is
required on your part if you are to obtain the fullest
measure of satisfaction and performance.

Whenever you need service, genuine Exmark parts,
or additional information, contact an Authorized
Service Dealer or Exmark Customer Service.

For complete warranty details, see
http://www.Exmark.com. You may also call

us 402-223-6375 to request a written copy of the
product’s warranty.

3

 

Содержание 116-8430

























Отзывы: