1 Faceplate
2 Chevron Cover
3 Red/Green Diffuser
4 Enclosure
5 Backplate
7 Junction Box
(Building Utility)
6 Wire Nuts
1
2
3
4
5
6
7
1 Faceplate
2 Chevron Cover
3 Red/Green Diffuser
4 Enclosure
5 Backplate
7 Canopy
8 Mounting Plate
9 Wire Nuts
10 Junction Box
(Building Supply)
6 Canopy Plug
1
2
3
4
5
6
7
8
9
10
1 Faceplate
2 Chevron Cover
3 Red/Green Diffuser
4 Enclosure
5 Backplate
7 Canopy
8 Mounting Plate
9 Wire Nuts
10 Junction Box
(Building Supply)
6 Canopy Plug
1
2
3
4
5
6
7
8
9
10
Back Mounting
• Drill 3/8” hole into the center of the
•
back plate (5). Drill 1/4” inch holes into
•
the ob-long holes on back plate (5) that
•
correspond to junction box (7) being
•
used.
• Feed leads through center hole and
•
make the proper connections. If using
•
120VAC, connect the black and white
•
leads to power supply. If using
• •
•
277VAC, connect the orange and white
•
leads to power supply. Route wires
•
through guide
posts located on back
•
plate.
• Feed excess wire into junction box
•
and secure back plate (5) to junction
•
box (7) using screws.
• Snap in arrows (2) to faceplate (1) as
•
required, storing unused arrows in a safe
•
place. Then snap faceplate (1) to housing
•
(4).
Ceiling Mounting
• Attach mounting plate (8) to junction
•
box (10).
• Feed transformer leads through top
•
hole, making sure to secure wire into
•
wire guides found at the edges of the
•
sign.
• Attach sign to canopy (7) by inserting
•
canopy into sign then sliding to the side to
•
lock (see back page of instruction
•
manual).
• Make proper lead connections. If using
•
120VAC, connect the black and white
•
wires to power supply. If using 277VAC,
•
connect orange and white wires to
•
power supply.
• Push excess wire into junction box.
• Align holes in canopy with those in
•
mounting plate. Use supplied screws to
•
secure canopy to mounting plate,
•
tightening until canopy is pulled tight to
•
ceiling.
• Snap in arrows (2) to faceplate (1) as
•
required, storing unused arrows in a safe
•
place. Then snap faceplate (1) to housing
•
(4).
• For double-faced signs, replace
•
backplate with extra EXIT faceplate.
End Mounting
• Attach mounting plate (8) to junction
•
box (10).
• Feed transformer leads through side
•
hole, making sure to secure wire into
•
wire guides found at the edges of the
•
sign.
• Attach sign to canopy (7) by inserting
•
canopy into sign then sliding to the side to
•
lock (see back page of instruction
•
manual).
• Make proper lead connections. If using
•
120VAC, connect the black and white
•
wires to power supply. If using 277VAC,
•
connect orange and white wires to
•
power supply.
• Push excess wire into junction box.
• Align holes in canopy with those in
•
mounting plate. Use supplied screws to
•
secure canopy to mounting plate,
•
tightening until canopy is pulled tight to
•
ceiling.
• Snap in arrows (2) to faceplate (1) as
•
required, storing unused arrows in a safe
•
place. Then snap faceplate (1) to housing
•
(4).
• For double-faced signs, replace
•
backplate with extra EXIT faceplate.
