EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 716 / 887

Test Functions

706

88000 Series

RTD/RTT (CPRI/OBSAI Framed L2)

Round Trip Time (OBSAI)

Indicates the time required for a bit to travel from one point to another.



RTT

indicates the round trip time measurement from the Base Station

going through the Remote Radio Head (including

Delay



1,2

) and

back to the Base Station. The

RTT

appearing on the diagram

corresponds to the average value.



Propagation Delay

indicates the propagation delay measured from

the Base Station to the Remote Radio Head (RRH) or vice-versa
assuming that the cabling in both directions are in the same cable
bundle. The

Propagation Delay

appearing on the diagram

corresponds to the average value.



Last

indicates the result of the last time/delay measurement.



Minimum

indicates the minimum time/delay recorded.



Maximum

indicates the maximum time/delay recorded.



Average

indicates the average time/delay value.



Unit

measurement selections are

(default) and



Delay



1,2

reports the internal delay introduced by the electronic

components in the Remote Radio Head (RRH).

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды