EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 660 / 887

Test Functions

650

88000 Series

FlexE Advanced

Reset/Manual Skew

Allows the selection of a relative delay in nanoseconds that will be
introduced for each PHY.



Reset Skew

sets all TX skew (ns) values to 0.



Manual Skew

allows setting the skew value for each PHY manually.



PHY TX Skew

PHY/Port

indicates the PHY/Port numbers and

All

which

represents the value for all PHY/Port when the

All PHY

check box

is selected.

Skew (ns)

allows setting the skew value for each PHY. Enter

directly the skew value in the field or use the “+” and “-” buttons to
respectively increment or decrement the skew value using the
defined

Skew Inc/Dec Size

value. Tapping and holding the “+” or

“-” button allows reaching the desired value faster using the
defined

Skew Inc/Dec Size

value. Range is from

1000

ns.



All PHY

, when selected, applies the change(s) to all PHYs at once.



Skew Inc/Dec Size (ns)

allows setting the increment/decrement

value that will be used when changing the Skew (ns) values using
the “+” and “-” buttons. Range is from

1000

ns.

PHY Skew Alarm Threshold (ns)

Allows setting the threshold value that will be used to declare a skew
alarm:

ns to

1000

ns, default is

300

ns (see

Excessive PHY Skew

page 449).

Default

button restores the default PHY skew alarm threshold value.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды