EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 653 / 887

Test Functions

Power Blazer

643

FEAC

Received Messages

Displays current and previous alarms/status and loopback commands as
well as the link activity for the received DS3 signal.



Link Activity



None (All 1’s)

: An all ones pattern (11111111 11111111) has been

detected in the last second.



Alarm/Status

: An Alarm/Status codeword has been detected in the

last second. An Alarm/Status is only detected when receiving at
least 10 consecutive occurrences of a specific codeword.



Loopback

: A Loopback command message has been detected in

the last second. A valid loopback command is detected only when
receiving 10 consecutive occurrences of a specific

Loopback

Command

immediately followed by 10 occurrences of a specific

Channel Codeword



Unassigned

: An unassigned message has been detected in the last

second. An Unassigned message is only detected when receiving
at least 10 consecutive occurrences of a specific unassigned
codeword. An

Alarm/Status

codeword is also reported since

Unassigned

is part of the

Alarm/Status

group.



Alarm/Status and Unassigned

displays the current and previously

received

Codeword

messages.



Current

indicates the last valid message, if any, received in the last

second of measurment.



Previous

indicates the message, if any, that was received just

before the current measurement.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды