EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 626 / 887

Test Functions

616

88000 Series

40/100/200/400G Advanced - CFP4/CFP8/OSFP/QSFP+/QSFP28/QSFP56-DD Control

CFP4/CFP8/OSFP/QSFP+/QSFP28/QSFP56-DD
MDIO/I2C Access Interface



MDIO/I2C - Bulk Read



Page Select

, available for QSFP I2C, allows selecting the I2C

address page:

0x00

(default) to

0xFF



MDIO/I2C Start Address

allows selecting the MDIO/I2C start

address:

0x0000

(default) to

0xFFFF

(MDIO)/

0x00FF

(I2C).



MDIO/I2C End Address

allows selecting the

MDIO/I2C

end

address:

0x0000

0xFFFF

; default is

0x00FF



Bulk Read

button reads and displays the data based on the

specified MDIO range (MDIO/I2C Start Address to MDIO/I2C End
Address).

Save to CSV

button allows saving the read MDIO/I2C’s addresses

and data to a CSV file.

Note:

The bulk read size is limited to 1024 addresses.



MDIO/I2C - Bulk Write



Bulk Write

button allows configuring and writing MDIO/I2C data

values for up to 20 addresses.

Page Select

, available for I2C, allows selecting the I2C address

page:

0x00

(default) to

0xFF

Address

and

Data

allows defining up to 20 MDIO/I2C addresses

and their data values: 0x0000 (default) to 0xFFFF for MDIO and
0x00 (default) to 0xFF for I2C.

Bulk Write

button writes the MDIO/I2C data values for each

MDIO/I2C address defined.

Default

button resets the MDIO/I2C page select, addresses, and

data values to their default values.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды