EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 375 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

365

TCP Throughput

TCP Throughput

From the

Test

menu, tap

Setup

,

Test Configurator

, and tap on the test

block.

TCP Mode

Since two units are required to perform a TCP Throughput test, one unit
must be the source (

Local

) unit and the other one the destination

(

Remote

). Set the TCP Mode on both units:

Local

(default) or

Remote

.

TCP Connection Configuration



Remote IP Address

, available with

Local

TCP mode, allows entering

the IP address of the remote unit.



Quick Ping

button automatically starts the quick Ping utility for the

remote IP address and provides either a successful or failed result. The
quick Ping uses 3 attempts, a Delay of 1 second, a Timeout of 2
seconds, and a Data Size of 32 Bytes. Refer to

Ping & Trace Route

page 686 for more options.



Accept Connection from IP

, available with

Remote

TCP mode, allows

entering the IP address of the local unit. The IP address

0.0.0.0

(default) listens to any TCP stream.



IP TOS/DS

, available with

Local

TCP mode, is configurable from

0x00

(default) to

0xFF

.



TCP Port

, available with

Local

and

Remote

TCP modes, allows the

selection of the TCP port number:

0

to

65535

(default is

50201

). For the

local unit, the specified TCP port will be used for the TCP initialization
algorithm with the remote unit. The following TCP segments sent by
the local unit will use the TCP port number replied by the remote unit.

«
...
373
374
375
376
377
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Sole Diesel Страницы: 8

Бренд: HABONIM Страницы: 9

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Magnescale Страницы: 3

Бренд: Yamaha Страницы: 92

iEP-5000G Series

Бренд: ASROCK Страницы: 2

Бренд: Runxin Страницы: 4

COMBIVERT F4-S/1.2

Бренд: KEB Страницы: 96

SmartScene IR Remote Series

Бренд: Thorlux Lighting Страницы: 2

Бренд: Cooper Страницы: 4

Бренд: Trenz Electronic Страницы: 21

Бренд: Nibe Страницы: 92

Бренд: Ublox Страницы: 58

Бренд: SAFERA Страницы: 32

Бренд: KATO VISION Страницы: 23

Бренд: IEI Technology Страницы: 6

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды