EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 374 / 887

Test Setup - Test Configurator, Timer, and System

364

88000 Series

Transceiver System (TA/TA4)

Transceiver System (TA/TA4)

Gives the transceiver system insertion counter and information on the
inserted transceiver system.

From the

Test

menu:



For iOptics, tap

Setup

Test Configurator

, tap

More...

from the

Device

Under Test

block, and on the

Transceiver System

tab.



For other tests, tap

Setup

Test Configurator

, tap on the interface

block and on the transceiver system (

TA/TA4-...

) tab.



For TA-SYNC, tap

Setup

Test Configurator

, tap on the clock block and

on the

TA-SYNC

tab. This tab is not displayed when Ext Clock Out is set

None

Port



Transceiver System Insertion Counter

indicates the number of time a

transceiver system has been inserted into this FTBx module port.



Transceiver System Parameters

are as follows:



indicates the name of the transceiver system.



Serial Number

indicates the serial number of the transceiver

system.



Revision

indicates the hardware revision of the transceiver system.



Battery

indicates the status level of the battery:

Good

Low

, or

Depleted



Optical Module Insertion Counter

indicates the number of time

an optical transceiver has been inserted into this transceiver
system port.

1. Not available with TA-SYNC.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды