EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 323 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

313

S-OAM and MPLS-TP OAM



Requesting MEP ID TLV

(G.8113.1) check box when selected (default)

determines if the Requesting MEP ID TLV is present in the LBM frame.
The

Requesting MEP ID TLV

check box is cleared and not selectable

when the

Continuous

check box is selected.



Priority

, available with S-OAM Mode or when VLAN is enabled (see

VLAN

on page 268), allows selecting the VLAN user priority:

(default)

. Refer to

VLAN ID and Priority

on page 842 for more information.



Drop Eligible

, available with S-OAM Mode or when VLAN is enabled

(see

VLAN

on page 268), when set to

Yes

(DEI = 1), the transmitted

frames will be dropped first on receipt when congestion occurs under
test. Drop Eligible is only configurable with

Unicast

address type,

otherwise is set to

(Default). Drop Eligible is set to

for

Frame

Delay

Frame Loss

, and

Synthetic Loss

functions.



Period

determines the transmission period of frames which is set to

100 ms

Period

is not applicable for Multicast address type or when the

Continuous

check box is selected.



TX Rate (%)

is the transmission rate of the LBM frame:

0.0001

95 %

for 10M,

99.5 %

for 100M,

99.95 %

for 1G,

99.995 %

for 10G LAN, and

92.8521 %

for 10G WAN. Only available with Loopback test function

when the

Continuous

check box is selected.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды