EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 241 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

231

Interface

RP3 Address (OBSAI Framed L2)



Source

identifies the source node of RP3 messages:

0000

1FFF

;

default is

1234

. The RP3 address 1FFF corresponds to the empty

message address that is dropped according to the standard.



Target

identifies the peer node that is receiving the RP3 messages:

0000

(default) to

1FFF



Peer Target

indicates the RP3 Peer Target Address; indicates a

mismatch when displayed in red.



Address Mismatch

check box when selected, cleared by default,

enables the monitoring of the mismatch between the Source and
received Peer Target addresses.

RP3 Message (OBSAI Framed L2)



Type

identifies the type of RP3 Data Message generated by the OBSAI

node:

WCDMA/FDD

(00010) - (default),

LTE

(01110),

GSM/EDGE

(00100), and

802.16

(01100).



Msg Grp/Frame (N_MG)

indicates the number of Message Group per

Frame parameter.



Msg/Grp (M_MG)

indicates the number of Message per Message

Group parameter.



Idle/Grp (K_MG)

indicates the number of Idle per Message Group

parameter.

ESMC

Note:

Available with Wander test application with SyncE rates.

Generated QL

allows the selection of the QL message that will be

generated. See page 512 for the list of QL message (default is

QL-DNU/DUS

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды