EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 180 / 887

background image

Test Setup - Test Configurator, Timer, and System

170

88000 Series

Clock



Offset (ppm)

displays the positive or negative frequency offset

between the standard rate specification and the rate from the received
signal. The background color is used to indicate if the received clock
meets (green) or not (red) the standard rate specification.

Ext Clock Out

Note:

Available when the

Clock Mode

is set to

Internal

,

Recovered

, or

Backplane

. Not available on 8870.

Allows setting the clock that will be generated.



Interface Type

allows the selection of the clock interface:

None

(default when DS1 is not supported),

DS1

(default),

E1

, and

2MHz

(default for 88460). For eCPRI BERT the interface type is fixed to

None

.

Ext Clock Out

on a green background indicates that a valid clock is

generated on the clock port.

LOC

on a red background indicates that no clock is generated on the

clock port.



Connector

either indicates the connector type used for the clock or on

8880 allows the selection of

Bantam

or

RJ48C

when the BNC

connector is used by the test application.



LBO

(Line Build Out), available with DS1 only, allows the selection of

the interface Line Build Out that meets the interface requirements over
the full range of cable lengths:

DSX-1 (0-133 ft)

(default),

DSX-1 (133-266 ft)

,

DSX-1 (266-399 ft)

,

DSX-1 (399-533 ft)

, and

DSX-1 (533-655 ft)

.

Signal

Standard Rate specification

DS1

1544000 ± 8 bit/s (± 4.6 ppm)

E1

2048000 ± 10 bit/s (± 4.6 ppm)

2MHz

2048000 ± 10 bit/s (± 4.6 ppm)

«
...
178
179
180
181
182
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: BADODOSECURITY Страницы: 8

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды