EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 632 / 803

background image

Test Functions

620

88000 Series

RTD

RTD

Note:

Available with Pattern client. Not available in Decoupled, Through, or
Through Intrusive mode.

Round Trip Delay (RTD) measurements are needed to quantify the time it
takes for a signal to cross the network and come back. Usually, transport
delay is due to two factors: long configured paths and transit times through
the network elements along the path. Therefore, RTD measurements are
significant in systems that require two-way interactive communication,
such as voice telephony, or data systems where the round-trip time directly
affects the throughput rate.

From the

Test

menu, tap

Functions

, and the

RTD

tab.

Note:

To do a Round Trip Delay test, the remote NE should be configured to
provide a loopback.

Note:

Be aware that RTD requires error free operation conditions to provide
reliable results. Therefore, RTD results could be affected by error injection
or error introduced by the network.

Mode

Allows the selection of the round trip delay test mode. Choices are

Single

(default) and

Continuous

.



Single

allows testing the round trip delay once.



Continuous

allows testing the round trip delay continuously in a

repetitive manner (one RTD measurement every 2 seconds).

«
...
630
631
632
633
634
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 168

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 29

Бренд: Panasonic Страницы: 37

Бренд: Panasonic Страницы: 9

Бренд: Magnescale Страницы: 132

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Yudian Страницы: 26

Бренд: eclisse Страницы: 40

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренд: YachtSafe Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды