manualshive.com logo in svg

EXFO Power Blazer 88000 Series, Руководство пользователя

Экспертный тестер сетей EXFO Power Blazer 88000 Series - надежное устройство для тестирования и мониторинга сетей. Для ознакомления с возможностями и настройками прибора скачайте бесплатное руководство пользователя на manualshive.com. Узнайте как максимально эффективно использовать этот инструмент для анализа сетевых проблем.

Поделиться
Скачать
background image

Test Results

Power Blazer

503

Summary (RFC 2544)

Throughput, Back-to-Back, Frame Loss, and 
Latency Subtests 

Throughput

, 

Back-to-Back

, 

Frame Loss

, and 

Latency 

For each subtest, its status (

-- 

(Idle), 

In Progress

, 

Completed

, or 

Aborted -

(reason)) and duration are displayed.

TX Frames

1

 and 

RX Frames

1

 display the transmitted and received 

frame counts of the subtest in progress. For 

Dual Test Set

, frame 

counts are available for both directions: from local to remote (

L->R

) 

and remote to local (

R->L

). For Dual Port topology, frame counts are 

available for both P1 to P2 (

P1->P2

) and P2 to P1 (

P2->P1

).

Trial #

1

 displays the current trial iteration of the subtest in progress 

when applicable. 

Val. #

1

 displays the current validation iteration of the subtest in 

progress when applicable. 

Step

1

 displays the current step of the subtest in progress when 

applicable. 

Displayed Results

: Select the displayed result mode: 

Current

, 

Minimum

 (default), 

Maximum

, or 

Average

. 

Throughput

/

Back-to-Back

/

Frame Loss

/

Latency

 table. 

Each frame size used for the test is displayed with its subtest statistics. 
Statistics values are displayed based on the 

Displayed Results

 setting. 

“--” indicates that the result is not available because the test has not 
run yet. While testing, one of the following messages is displayed for 
each frame size: 

Initializing

, 

Learning

, 

Testing

, 

Waiting

, 

Not 

measurable

, 

Aborted

, 

Link is Down

, or 

MAC not resolved

. 

Dir.

 (Direction), available with 

Dual Test Set

 or 

Dual Port

 topology, 

indicates respectively results from local to remote (

L->R

) and remote 

to local (

R->L

), or P1 to P2 (

P1->P2

) and P2 to P1 (

P2->P1

). 

1. Only displayed once the test is started. 

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

jbc DI Series Manual preview
DI Series
Бренд: jbc Страницы: 4
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Бренд: Fairchild Страницы: 2
Fagor 101 Operating Manual preview
101
Бренд: Fagor Страницы: 103
Abicor Binzel EWR Quick Install Instructions preview
EWR
Бренд: Abicor Binzel Страницы: 8
CAME TWIN Maintenance Instructions Manual preview
TWIN
Бренд: CAME Страницы: 98
CAME ZL19N Installation Manual preview
ZL19N
Бренд: CAME Страницы: 16
CAME RIOED8WS Instructions Manual preview
RIOED8WS
Бренд: CAME Страницы: 8
Gardner Denver AirSmart G2 Installation Manual preview
AirSmart G2
Бренд: Gardner Denver Страницы: 22
B&G NMEA 2000 Installation Manual preview
NMEA 2000
Бренд: B&G Страницы: 2
hager coviva Smartbox TKP100A Quick Manual preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 4
Vag ZETA Operating And Maintenance Instructions Manual preview
ZETA
Бренд: Vag Страницы: 12
Lamtec ETAMATIC Manual preview
ETAMATIC
Бренд: Lamtec Страницы: 136
u-blox M8 Series Hardware Integration Manual preview
M8 Series
Бренд: u-blox Страницы: 28
Saluki SMR Series Quick Start Manual preview
SMR Series
Бренд: Saluki Страницы: 13
Fancom MRK.1 Manual preview
MRK.1
Бренд: Fancom Страницы: 23
Beninca HEAD Operating Instructions Manual preview
HEAD
Бренд: Beninca Страницы: 7
IDEATEC DLC4000 User Manual preview
DLC4000
Бренд: IDEATEC Страницы: 32
Broadcast Tools AVR-8 Installation And Operation Manual preview
AVR-8
Бренд: Broadcast Tools Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды