EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 465 / 803

background image

Test Results

Power Blazer

453

S-OAM and MPLS-TP OAM



Invalid Payload

indicates the count of received LBR frames having

either a TLV type different than the one transmitted, Bit error or wrong
data value detected in the data payload of a Data TLV, Bit error, Pattern
Loss, or Pattern Type mismatch of a Test TLV.



Successful

indicates the count of received LBR frames having no

errors.



Failed

indicates the count of LBR frames declared as invalid.

Test



Status

displays the status of the test function (refer to page 511).



TX TST

indicates the count of transmitted TST frames.



RX TST

indicates the count of valid TST frames received. A valid frame

for S-OAM has its source MAC address matching the Peer MEP MAC
address; destination MAC address matching either the unit port Unicast
MAC address or a Multicast class 1 address

1

; and VLANs matching the

unit port VLANs. A valid frame for MPLS-TP OAM has its destination
MAC address matching either the unit MAC address, FF:FF:FF:FF:FF:FF,
or 01:00:5E:90:00:00; VLANs matching the unit port VLANs; and MPLS
Labels matching the local MPLS Label Stack configuration.



Invalid TST

indicates the count of TST frames received from the peer

MEP with incorrect MEG/MD level.



Invalid Payload

indicates the count of received TST frames having

either an unsupported pattern type, or bit error / pattern loss detected
in the payload.



Successful

indicates the count of received TST frames having no

errors.



Failed

indicates the count of TST frames declared as invalid.

1. Refer to

Unicast/Multicast Addresses for Ethernet OAM

on page 757 for more information.

«
...
463
464
465
466
467
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Garmin Страницы: 12

Бренд: Aaeon Страницы: 76

Бренд: Eaton Страницы: 100

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Valcom Страницы: 6

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Бренд: Centurion Страницы: 16

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

Бренд: Apex Toys Страницы: 7

Бренд: S&C Страницы: 26

Diaval AF Series

Бренд: Comeval Страницы: 10

SMARTCONNECT SMART/REP

Бренд: Zeta Alarm Systems Страницы: 48

Бренд: Sherlotronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды