EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 337 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

325

System

System

From the

Test

menu, tap

Setup

, and

System

Factory Default



Restore Default

button restores the factory default settings for all test

applications.



Restore Default at Start-Up

check box when cleared (default),

reloads the last configuration settings when the application is
launched; when selected, the factory settings are restored.

Remote Control

User Information

allows a user to leave a message to other users

connected on the same module. Up to 80 characters are allowed.

Time Zone

allows the selection of the time zone source.



Local

(default) uses and displays the time from the 88000 Series

module or from the PC for a Remote ToolBox session.



Test Equipment

, available for a Remote ToolBox session, uses and

displays the time from the 88000 Series module.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды