EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 325 / 803

Test Setup - Test Configurator, Timer, and System

Power Blazer

313

Streams - Global

Streams - Global

From the

Test

menu, tap

Setup

Test Configurator

, the protocol block, and

the

Global

tab.

The following parameters are displayed and configurable per stream.



Check boxes:

The first check box (top-left) allows enabling stream(s) sequentially
within the limit of the link capacity.

The check boxes next to the stream numbers allow enabling each
stream individually within the limit of the link capacity.



Stream Name

indicates the name of each stream. Tap on the

Stream

Name

button to modify the name of each stream.



Frame Size

indicates the frame size of each stream. Tap on the

Frame

Size

button to modify the frame size of each stream.



TX Rate

indicates the transmission rate for each stream. Tap on the

TX Rate

button to modify the transmission rate (see page 319).



Framing

indicates the framing of each service. Tap on the

Framing

button to modify the

Frame Format

Network Layer

Transport Layer

VLAN

, and

MPLS

when applicable (see

Modify Frame Structure

from

the

MAC/IP/UDP

on page 204).



VLAN

indicates the ID and Priority of each VLAN level for each stream.

Tap on the

VLAN

button to modify the VLAN settings (see

VLAN

from

the

MAC/IP/UDP

tab).

1. See the Profile tab for more information.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды