EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 133 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

121

Modify Structure Button



PHY Type

allows selecting the 100GE (4 Lanes) CFP4/QSFP transceiver

PHY type:

LR4/ER4

(default),

SR4

,

CWDM4

,

CLR4

, or

Other

. The PHY

type when set to any except

LR4/ER4

, allows enabling RS-FEC (see

page 182); ensure both ends of the circuit have the FEC enabled. Only
available with 100GE (4 Lanes) framed Ethernet interface.



Primary Port / Secondary Port

, available with Through Mode test

application, allows selecting the module’s ports that are respectively
used as primary (Port 1) and secondary (Port 2) port. The configuration
of the network configuration parameters will be available on the
Primary Port only.



Connector

allows the selection of the module’s port.

Interface/Rate

Connector

a

a.

Availability of connectors depend on the model.

8870/8880

88200NGE

88260

88400NGE

400GE (8 Lanes) [425 Gbit/s]

-

-

-

Port 1 - CFP8

100GE (4 Lanes) [103.125 Gbit/s]

-

Port 1 - CFP4
Port 2 - QSFP

b

b.

This port accepts QSFP+ or QSFP28 transceivers.

-

-

40GE (4 Lanes) [41.25 Gbit/s]

-

Port 2 - QSFP

-

-

25GE

-

-

Port A1 - SFP28
Port A2 - SFP28
Port B1 - SPF28
Port B2 - SFP28

-

10GE WAN
10GE LAN
1GE Optical
100M Optical

Port 1 - SFP+
Port 2 - SFP+

Port 1 - SFP+

-

-

10/100/1000M Electrical

Port 1 - RJ45
Port 2 - SFP+
(RJ45)

c, d

c.

Only available as a second port when the test application requires two ports.

d.

Ethernet 10/100/1000M electrical is supported when using an active copper SFP.

Port 1 - SFP+
(RJ45)

-

-

«
...
131
132
133
134
135
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Parker Страницы: 28

Бренд: Lamtec Страницы: 22

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: Olsberg Страницы: 68

Бренд: Parkside Страницы: 65

Бренд: TCS Страницы: 16

Бренд: Zamel Страницы: 2

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды