manualshive.com logo in svg

EXFO FTB-860, Руководство пользователя, Страница: 153 / 409

Поделиться
Скачать
EXFO FTB-860 Скачать руководство пользователя страница 153

NetBlazer

141

10 Through Mode Test Setup and 

Results

The Through Mode

 

test feature is intended to monitor Ethernet traffic 

between two end points, with as much transparency as possible. This type 
of application allows in-line monitoring without using an external tapping 
module, a switch mirror port or any other traffic redirection scheme simply 
based on the interface setup parameters. To configure 

Interface

 setup, see 

Interface

 on page 280. In Through Mode test, both Port 1 and Port 2 are 

active and the link status, and speed is displayed for both ports. Statistics 
are cumulated on traffic entering and leaving the test set in both directions. 
Configuration of the active port used when Through Mode test is selected 
will be copied to the other port. When the test is not running, the module 
listens for Remote Loopback & DTS, only on active port.

Note:

Through Mode

 is not available on the FTB-860GL.

Note:

The 

Through Mode 

test is only available when the Through Mode software 

option (

ETH-THRU

) is enabled.

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов