EXFO FTB-1 Скачать руководство пользователя страница 433

Страница: 433 / 675

Test Results

NetBlazer

421

Summary (Link OAM)

Summary (Link OAM)

From the

Test

menu, tap

Results

, and the

Summary

tab.



Test Status

displays the current status of the Link OAM test. The global

test pass/fail verdict is displayed next to the

Test Status

when enabled

(see

Pass/Fail Verdict

on page 275).



Start Time

Indicates the date and time the test has been started. The

date and time is reset every time the test is restarted or reset.



Power Recovery

when displayed, indicates that the test has

automatically recovered from a power failure. The number of
occurrences is also displayed next to the

Power Recovery

field. Refer

Power Failure Recovery

on page 559.



Logger Full

, when displayed, indicates that the logger is full. Refer to

Logger and Alarms/Errors Logger

on page 362.

Alarms



Link OAM

indicates that no OAM Information PDUs were received for 5

seconds.



Critical Event

: Indicates that the OAM link partner has sent a critical

event notification (bit 2 of the Flags field is set to 1).

Test Status

Description

The test is not running or results are not available.

In Progress

The test is running.

Completed

The test is completed, stopped at the planned time, or manually stopped when there is no
set timer.

Aborted

The test is interrupted; stopped before the set timer.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды