manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 374

Test Results

362

FTB-700G/800 Series

Logger and Alarms/Errors Logger

Logger and Alarms/Errors Logger 

The Logger page displays color-coded events and pass/fail verdict.

From the

 Test

 menu, tap 

Results

, and the 

Logger

 or 

Alarms/Errors 

Logger

 tab.  

Sort By 

Sort By

: Select the sorting order of the event logger entries: 

ID/Time

 (default) displays the event logger entries in numeric 

ascending order based on the 

ID

 column of the event logger table. 

Event

 displays the event Logger entries in alphanumeric ascending 

order based on the 

Event

 column of the event logger table.

Time Mode 

Relative

 displays the time elapse since the beginning of the test or 

since the last test reset. The format of the time is Dd HH:MM:SS. 

Absolute

 (default) displays the date and time the event occurred. 

The time format depends on the FTB-1 time settings. 

For 24 hours, the time format is MM/DD HH:MM:SS.

For 12 hours, the time format is MM/DD HH:MM:SS <AM or PM>.

The logger table provides the following event logger information.

ID

: Indicates the event identification number. The events are 

sequentially numbered. 

Time

: Indicates when the event has been detected. 

Event

: Provides the event type and threshold crossing information. 

Duration

: Indicates the number of seconds within which the event 

occurred. Test events like 

Test Started

 and 

Test Stopped

 will have no 

duration. 

Details

: Provides contextual information including the pass/fail verdict. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды