EXFO CT440 Series Скачать руководство пользователя страница 89

Страница: 89 / 169

CT440

Troubleshooting

Warning & Error Messages

The following table lists all the possible warning and error messages, and how to handle
them.

Trouble

Possible Resolution

The CT440 is not recognized by the

computer

See

Activating the USB Driver

on page 88.

The CT440 GUI does not start

See

Warning & Error Messages

on page 83.

The CT440 comes offline during

use

Restart both GUI and instrument to detect the CT440 again.

The GUI displays an error or

warning message

See

Warning & Error Messages

on page 83.

The

icon appear in the GUI (at

the left of the date and time)

See

Warning & Error Messages

on page 83.

Error or warning

Possible Cause

Possible solution

The

icon appear in the

GUI, at the left of the date

and time (on CT440 with

PDL option only).

Some points are missing in

the PDL calculation: the

CT440-PDL could not

calculate PDL for a few

measurement points.



Verify that the CT440-PDL is set on a flat

stable surface without vibration.



Verify that optical connectors are clean.



Verify that optical connectors are properly

connected to the CT440-PDL and tightly

locked in position.



Use the 6-state PDL measurement

method: in the

Scan Parameters

window,

select

6 States

in the

PDL Method

list (see

Configuring Scan Parameters

on page 35).

No Supported Languages
- Unable to open resource
files

The CT440 GUI uses

LabVIEW2013 RunTime. If

the CT440 GUI does not

start, it may be necessary to

repair the RunTime files.



From the Windows Control panel, in the

Remove Programs

window, right-click

the National Instruments program and

select

Unistall/Change



Repair the NI LabVIEW Runtime Engine

2013.



Restart the PC.

[warning code 100]
Mode hops on the scan

Mode hopping occurred

during the scan on one TLS.

Make sure the source performances meet the

requirements detailed in

Product Features

page 1.

[warning code 101]
Scan speed too low



The mean sweeping

speed of the TLS is too

low (< 8nm/s)



The reference file is not

located in the correct

folder.



Raise the scan speed.



Make sure the reference file is located in

the proper

Calib

folder:

C:\Users\Public\Documents\EXFO\CT440\

Calib

Содержание CT440 Series










































































































































































Результаты поиска

Содержание CT440 Series

Отзывы:

Похожие инструкции для CT440 Series

Бренды по названию

Популярные бренды

EXFO CT440 Series, Руководство пользователя

Результаты поиска

Содержание CT440 Series

Отзывы:

Похожие инструкции для CT440 Series

Бренды по названию

Популярные бренды