Exalt EX-4.5r GigE Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 132

background image

Exalt Installation and Management Guide

EX-r Series GigE Digital Microwave Radios

201872-003

81

2015-10-23

Pow er/ Ethernet Connector

This connector is the primary connector on the radio, and must be connected to provide power to the
radio, and primary Ethernet communications for traffic and Ethernet. Figure 48 illustrates the pin
orientation and functionality for this connector.

The Ethernet connector implements Auto-MDIX, and therefore either ‘straight’ or ‘crossover’
Ethernet cables may be used, independent of the wiring of the connected device. The wiring follows
typical wiring for Power-over-Ethernet (PoE), however the power consumption requirement for the
r-Series radio does not allow for ‘standard’ (802.3af) PoE, and only the Exalt power injector shall be
used. In addition, the Exalt power injector provides critical reset capability that would not be available
from a generic PoE injector, even if the power consumption requirement is met.

Figure 48 Power/Ethernet connector

Ethernet 2 Connector

This is the secondary connector for Ethernet on the radio. Use it to connect other networking
equipment to the radio system or for the primary data interface when the Power/Ethernet connector is
being used for out-of-band management applications. The pin assignments are the same for this
connector as the PoE(1) connector, but without any power connections.

Pin

Function

1

Paired with Pin 2

2

Paired with Pin 1

3

Paired with Pin 6

4

+DC Power (48V) In

5

+DC Power (48V) In

6

Paired with Pin 3

7

-DC Power (48V) In

8

-DC Power (48V) In

«
...
87
88
89
90
91
...
»

Содержание EX-4.5r GigE





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EX-4.5r GigE

Бренд: Uniden Страницы: 32

Heritage Bluetooth

Бренд: HAEGER Страницы: 40

Бренд: Denver Страницы: 13

Бренд: Radio Shack Страницы: 4

Бренд: Harbor Freight Tools Страницы: 11

Бренд: SpotterRF Страницы: 2

Бренд: Insignia Страницы: 29

Бренд: Uniden Страницы: 12

Бренд: TRX Страницы: 28

Бренд: Master Tailgaters Страницы: 6

Бренд: Kambrook Страницы: 6

Бренд: Clatronic Страницы: 14

Бренд: GME Страницы: 40

Бренд: Sencor Страницы: 14

Warwick W-59-IP

Бренд: Fisher Страницы: 20

Бренд: ApexRadio Страницы: 2

MPI-II LBI-38558B

Бренд: Ericsson Страницы: 14

Бренд: Hello Kitty Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды