Exalt EX-4.5r GigE Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 132

background image

Exalt Installation and Management Guide

EX-r Series GigE Digital Microwave Radios

201872-003

24

2015-10-23

LED Indicators

Table 3 provides details of the LED indicators on the EX-r Series GigE radios. Note that there are two
LEDs, labeled top and bottom, associated with each connector. See

for information on

how the Exalt GUI displays LED status.

RESET Button

There is only one external control on the EX-r Series GigE radios system, a button labeled “RESET”
located on the power injector. This button performs a critical system parameter reset.

Use the reset function if the IP address and/or passwords are lost. Use the following steps to perform a
critical parameter reset:

1

Remove power from the radio by disconnecting the AC adapter from the power injector.

2

Hold down RESET button on the power injector while applying power.

Hold the RESET button down through the whole power cycle and monitor the DATA+POWER
left LED on the power injector. Release the RESET button only after the LED is in the steady state
(approximately 2 minutes).

3

Release the RESET button.

The following configurations are reset on the radio:

•

IP address = 10.0.0.1

Table 3 LED indicators

Location

Type

Function

TDM 2&4

Green LED

Solid when T1 clocking is present for input #2.

TDM 2&4
Bottom

Green LED

Solid when T1 clocking is present for input #4.

TDM 1&3

Green LED

Solid when T1 clocking is present for input #1.

TDM 1&3
Bottom

Green LED

Solid when T1 clocking is present for input #3.

Sync Out

Green LED

Solid when radio is configured as sync source.

Sync Out Bottom

Green LED

Solid when synch source is external (GPS).

Ethernet 2

Green LED

(Future implementation.)

Ethernet 2
Bottom

Green LED

(Future implementation.)

Sync In/RSL

Green LED

Solid when valid Sync In connection is detected.

Sync In/RSL
Bottom

Green LED

Unused.

Power/Ethernet

Green LED

Solid when proper power is applied.

Power/Ethernet
Bottom

Green LED

(Future implementation)

Pow er I njector

DATA+POWER
Left

Green LED

Solid when no alarm conditions are present.

Flashing when in Reset mode.

DATA+POWER
Right

Green LED

Solid when proper power is applied.

«
...
30
31
32
33
34
...
»

Содержание EX-4.5r GigE





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EX-4.5r GigE

Бренд: Teac Страницы: 17

Бренд: Radionette Страницы: 152

Бренд: Lanzar Страницы: 12

Бренд: Radio Shack Страницы: 12

Бренд: AudioSonic Страницы: 44

Бренд: perfect pro Страницы: 116

Бренд: Oricom Страницы: 6

MicroTalk PMR300

Бренд: Cobra Страницы: 25

Бренд: Radio Shack Страницы: 9

Бренд: Ranger Communications Страницы: 29

Бренд: OnCourt OffCourt Страницы: 2

Бренд: Emerson Страницы: 12

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 19

Бренд: Emerson Страницы: 17

Бренд: Emerson Страницы: 12

CKD1100, CKD1100BL, CKD1100GN,

Бренд: Emerson Страницы: 30

Бренд: Emerson Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды