Exabyte VXA-2 AUTOPAK1X7 Скачать руководство пользователя страница 87

Страница: 87 / 104

CTOBER

2002

XABYTE

VXA-2 A

UTO

AK1x7

UTOLOADER

ACKING

THE

UTOLOADER

ACKING

THE

UTOLOADER

Use the original packing materials to pack the autoloader. You will also need

banding material.

To pack the autoloader, follow these steps and refer to

Figure 7-9

Place the autoloader on the cushion in the bottom of the box.

Insert the empty accessory box into the autoloader box.

Place the antistatic bag over the autoloader, then place the autoloader into

the box.

Caution

To avoid damaging the autoloader and voiding your warranty, be sure to use the

original shipping materials (or replacement materials obtained from your vendor)

when repacking and shipping the autoloader. Do not use the shipping carton and

packing materials to ship items other than an autoloader.

Important

If you are shipping the autoloader for repairs, do not include

the accessories.

Figure 7-9

Packing the autoloader for shipment

Accessory box

Содержание VXA-2 AUTOPAK1X7









































































































Результаты поиска

Содержание VXA-2 AUTOPAK1X7

Отзывы:

Exabyte VXA-2 AUTOPAK1X7, Руководство по эксплуатации продукта, Страница: 87 / 104

Результаты поиска

Содержание VXA-2 AUTOPAK1X7

Отзывы: