Installation and Commissioning
Instructions
Note: HP2000 required for commissioning
Ex-Or
Haydock Lane, Haydock, Merseyside WA11 9UJ
Tel: +44 (0)1942 719229
Fax: +44 (0)1942 272767
Email: [email protected]
www.ex-or.com
At the end of their useful life
the packaging and product
should be disposed of via a
suitable recycling centre.
Do not dispose of with normal
household waste.
Do not burn.
MLS2500D / MLS2500DF
MLS2500DWL* / MLS2500DWLF*
MLS2500DALI / ML2500DALIF
MLS2500DALIWL* / MLS2500DALIWLF*
Digital Mid Range LightSpot
*
with Wireless OneSwitch facility
MLS2500D(WL)
MLS2500DALI(WL)
MLS2500D(WL)F
MLS2500DALI(WL)F
ii) Switching Photocell Only (Passive Photocell = YES)
Use Passive mode in applications where light level regulation is not required (e.g. when controlling non-dimmable
ballasts), but it is desirable to hold off the controlled lighting when natural light is sufficient. The parameter Set-Point
Low on the HP2000 menu is designed to programme the MLS2500D's passive photocell set point, which
determines whether the lights will be allowed to turn on as an unoccupied area is entered. The threshold is
programmed as a number between 1 (darkest) and 1023 (brightest). This number is not scaled to correlate with ‘lux’
measurements made using a light meter, but nevertheless is a true representation of the light level perceived by the
MLS2500D.
In order to assist with selection of the appropriate Set-Point Low setting, the light level currently perceived by the
detector (in terms of a number between 1 and 1023) can be viewed on the HP2000 screen briefly following a
download operation. The number represents the light level immediately before the download took place.
Tip: Turn
the lights off first (using user-remote found in utilities) if you want to measure the perceived light level with no
contribution from the controlled lighting.
Technical Data
MLS CABLE: 1.5mm sq unscreened twisted-pair (applicable when detector used as part of a full MLS Digital
Managed Lighting System); see Application Note AN4001.
OPERATING VOLTAGE: 230V ~ 50Hz (UK & Europe).
SWITCH CAPACITY: 10 Amps max any lighting load except incandescent lamps: 1500W max (at 230V~).
MAX RECOMMENDED MOUNTING HEIGHT: 3.5m.
RANGE: Adjustable up to 20m.
OFF DELAY: 10 seconds to 96 hours.
WEIGHT: 160g.
COLOUR: White.
MATERIAL: Flame retardant PC/ABS.
IP RATING:
43 when ceiling mounted, 4X when wall mounted.
Contact Ex-Or Technical Helpline on 01942 719229 for guidance on installation and commissioning.
Important Additional Notes
in order
to achieve a predicted lamp life. Please check with the manufacturer of the luminaires to ensure that they are
compatible with automatic controls in this respect.
1.
All terminals on this product are provided for final connections. It is not intended that the product be used as a junction
box for looping cables.
2.
Although nominally 12V, the dimming output is not ELV and therefore should be treated with the same respect as mains
with regard to wiring practice.
3.
Take care when choosing a location for this equipment since this type of device is capable of detecting large moving
metal objects well beyond the normal range at which it is sensitive to human targets.
4.
Please note that, although configurable as a regulating photocell, [closed-loop dimming according to daylight], due to
the probable corner-of-room location where there will be excessive influence by daylight reflected from the walls, this
product is not intended to achieve precise light level regulation measured on the working plane.
5. This equipment switches lights no more frequently than would a responsible human occupant. However,
manufacturers of some lighting types (e.g. ‘2D’ luminaires) may specify a maximum number of switching cycles
W4364A
WMK
Wall-mounting kit for MLS2500D
(Supplied assembled)
Vertical installation
Use this method of mounting for racking aisle
applications and where adjustment in the
vertical plane will give improved control over
the precise point of entry detection.
Horizontal installation
For general applications where
ceiling mounting is not
convenient and wide angle
coverage in the horizontal plane
is desirable. The WMK can be
screwed to a hard surface or the
lid of a conduit stop-end box.
Exploded view of MLS2500DF
for fixing into ceiling tiles.
