EWM Expert XQ 2.0 Скачать руководство пользователя страница 52

Страница: 52 / 92

Operating the machine control

Change welding procedure (Arc)

099-00L105-EW501

07.06.2019

5.7 Change welding procedure (Arc)

In this menu the user can change the welding procedure based on the preselected material, wire and gas

(change of process based on welding task).
For changing the welding task (JOB)

> see 5.6 chapter

Enter the menu:

Figure 5-29

5.8 Online data transfer (network)

For machine variants with network capability (LG/WLG) only!

The network is used to transfer welding data from manual, automated and welding machines. It can in-

clude as many welding machines and computers as require and the collected data can be retrieved from

one or several server PCs.
The Xnet software allows the user to monitor all welding parameters in real time and/or to subsequently

analyse the saved welding data. The results can be used for process optimisation, welding calculations or

checking welding wire batches.
Depending on the welding machine the data are transferred to the server via LAN/WiFi and can then be

accessed in a browser window. The user interface and web-based design of the software offer the possi-

bility to analyse and monitor the welding data via a tablet PC.

5.8.1 Wired local network (LAN)

Status description

Status display

No physical connection to a network

Deactivated LAN symbol

Connection to the network, the machine has been

configured, no data transfer

Activated LAN symbol

Connection to the network, the machine has been

configured and transfers data

LAN symbol flashing

Connection to the network, the machine has been

configured and tries to connect to the data server

LAN symbol flashing in the specified rhythm

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды