EWM cool50-2 U40 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 26

EWM cool50-2 U40 Скачать руководство пользователя страница 12

Design and function

Cooling module assembly/disassembly

12

099-008603-EW501

27.07.2016

5.4

Cooling module assembly/disassembly

Assembly and disassembly is very simple and doesn't require any tools.

Figure 5-1

• Open out all four screw connectors on the cooling module as far as they will go.
• Position the welding machine precisely with the machine's feet in the openings of the screw

connectors provided on the cooling module.

• Push all four screwed connectors back in as far as they will go.

WARNING

Risk  of accidents  due to screw  connectors  that are not  locked!
Attention  must  be paid to  cleanliness and correct  installation
when mounting a power source  with a cooling module. The
cooling module could  become loose if not  properly mounted,
thereby causing  serious  injuries.

• Remove dirt from the feet of the power source's unit and the screw

connectors of the cooling module before mounting.

• Check that the connections are locked in place before each

transport
(push the screw connections back in as far as they will go)!

CAUTION

Risk  of accidents  due to supply  lines!
During  transport,  attached supply  lines (mains  leads, control  cables, etc.) can cause
risks,  e.g. by causing  connected machines to  tip over and injure persons!

• Disconnect all supply lines before transport!

«
...
10
11
12
13
14
...
»

Содержание cool50-2 U40



























Отзывы:

Нет отзывов