CONV Pelco To Bosch - firmware 0.01.xx
Ewimar Sp. z o.o.
www.ewimar.pl
Made in Poland
6. Red LED: Command „DR-x”.
Configuration for Red LED operation.
DR-0
– Indicates the translation and sending commands to
Bosch cameras - only if the controlled camera address is configured in the converter.
DR-1
– Indicates wrong packets received on Port 1 - wrong protocol, incorrect transmission
speed or transmission errors due to the use of poor quality cable..
7. Supported camera addresses: Command „CAx-y”.
The converter contains a camera table, the capacity of which depends on the license entered - by
default
16
for the
Standard
version and
1
for the
Lite
version. The table should be assigned
camera addresses in the range from 1-254, which will be supported by the converter.
The
x
character mean the position number in the table,
y
mean supported camera address (1-
255) entered at that position.
Choose the position number and assign an address to it. Example: To assign camera address
128 to position No 1, enter:
CA1-128
.
The order of the addresses in the table does not matter if the addresses repeat, only the first one
matters.
8. Special: Command „Sxxxxxx”.
Execution of a special command, for example entering the license code..
9. Address shift: Command „CSx-y”.
Described in the extended manual downloaded with the "
Get user manual
" button.
Always active in
Lite
version, active in
Standard
version after purchasing the license.
10. Advanced joystick correction: Command „CPx-y” i „CTx-y”.
Described in the extended manual downloaded with the "
Get user manual
" button.
Always active in
Lite
version, active in
Standard
version after purchasing the license.
List of translated commands from the Pelco keyboard
Controlling the camera using a Pelco keyboard directly depends on its functionality..
Nr
Command from Pelco keyboard
Bosch camera function
1
Move Up / Down / Left / Right
Move Up / Down / Left / Right
2
Zoom in / Zoom out
Zoom + / Zoom -
3
Focus Far / Focus Near
Focus Far / Focus Near
4
Iris open / Close
Iris Open / Close
5
Auto Pan
Scan 360
˚
(AUX-1-ON)
6
Auto Scan
Auto scan with left / right limit (ON-2-ENTER)
7
Left limit
Set left limit for Auto Scan (SET-101-ENTER)
8
Right limit
Set right limit for Auto Scan (SET-102-ENTER)
9
Learn Pattern ( Dowolny numer)
Pattern A record (ON-100-ETER)
10
Stop Learn ( Dowolny numer)
End record Pattern A (OFF-100-ENTER)
11
Run Pattern ( Dowolny numer)
Continuous Playback Pattern A (ON-50-ENTER)
12
Call Preset 95
Entry to menu (ON-46-ENTER)
13
Call preset 96
Unlock advanced menu (OFF-90-ENTER)
14
Call preset 97
Disable OSD (OFF-46-ENTER)
15
Call preset 101
Show left limit (SHOT-101-ENTER)
16
Call Preset 102
Show right limit (SHOT-102-ENTER)
17
Call preset 111
Stop record pattern A (OFF-100-ENTER)
18
Call preset 112
Stop record pattern B (OFF-101-ENTER)
19
Call preset 113
Edit Tour 2 Custom (SHOT-900-ENTER)
20
Call preset 114
Auto Pan/Scan 1 Speed (ON-14-ENTER)
minus
21
Call preset 115
Tour Speed 1 (ON-15-ENTER)
minus
22
Call preset 116
Scan left / light (ON-2-ENTER)
23
Call preset 120
Continuous Playback Pattern A (ON-50-ENTER)
24
Call preset 121
Single Playback Pattern A (ON-51-ENTER)
25
Call preset 122
Continuous Playback Pattern B (ON-52-ENTER)
