Evoqua WALLACE & TIERNAN SFC Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 288

background image

SFC

Maintenance

7.

227

4

Rinse the fine filter with water, replace if necessary.

5

Place the fine filter into the filter unit.
Ensure that the O-ring is fitted correctly (insert as far as
possible).

6

Fit the filter unit. Ensure that it is fitted in the correct position.

7

Tighten both knurled nuts (A).

7.3

Maintaining membrane sensors

For the membrane sensor maintenance procedure, see 4.2.6
“Membrane sensors”.

Please refer to instruction manual „membrane sensor for free
chlorine FC2“ and „membrane sensor for total chlorine TC3“.

7.4

Maintaining Redox electrode

Depending on how dirty the sample water is, the Redox electrode
must be cleaned at certain intervals. Unclean water causes the
measurement to be very slow. At the same time, the Redox
voltage is frequently indicated as too low. The surface of the
platinum disc is usually soiled. This may be to some extent in the
form of an invisible coating. In particular, the ceramic electrode
diaphragm may also be soiled or coated with lime deposits.

To clean the soiled metal disc, the Redox electrode is removed
from the flow-through adapter and cleaned with a paper towel; use
diluted hydrochloric acid (up to 10 %), if necessary. Scouring
cleaner may not be used because it may clog the diaphragm. Then
rinse well with water. Do not touch the platinum electrode after
rinsing in order to keep oil from fingers off them. To remove lime
deposits, immerse the electrodes just past the diaphragms into
hydrochloric acid (10 %); allow several minutes for this to react and
rinse with clear water.

Please note

Do not use any other chemicals than those described here. These
could damage the electrode.

«
...
225
226
227
228
229
...
»

Содержание WALLACE & TIERNAN SFC

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WALLACE & TIERNAN SFC

Бренд: Saito Страницы: 90

Бренд: Vancare Страницы: 31

Бренд: Eaton Страницы: 16

DBI SALA Pro Series

Бренд: 3M Страницы: 24

medialon Showmaster Go

Бренд: 7th Sense Страницы: 2

Бренд: eclisse Страницы: 40

Бренд: Safeline Страницы: 8

Бренд: RAKwireless Страницы: 6

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

WAGO-I/O-SYSTEM 750 XTR Series

Бренд: WAGO Страницы: 272

Бренд: WAGO Страницы: 450

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды