Evoqua DEPOLOX POOL COMPACT WALLACE & TIERNAN Скачать руководство пользователя | Manualshive

Страница: 57 / 88

background image

DEPOLOX® Pool Compact

6. Operation

57

EN

6.3.5 ”Login” menu

Log in on the desired user level in this menu.
Depending on the user administration confi-
guration (chapter 6.3.8), three user levels with
different rights are available. You can enter
either a locking code or a password. The cur-
rently logged in user is also displayed in this
screen. If the locking code entry is corrected,
the pattern is displayed in green. If an incor-
rect locking code is entered, the pattern is
displayed in red. If the user data can no longer
be found, please contact your service partner.

1 Call up the HOME menu.
2 Tap

the

symbol.

3 Tap the

Login menu.

4 Enter locking code or password.

6.3.6 Settings” menu

The device settings not relating to measured
values are configured in the Settings menu.

1 Call up the HOME menu.
2 Tap

the

symbol.

3 Tap

the

Settings Menu.

4 Enter desired settings.

Acknowledge:

Input specifies whether an alarm is defi-
ned as an alarm without acknowled-
gment, an alarm with simple
acknowledgment or acknowledgment
with Reset.

Delay time:

Switch-on delay time.

Relay:

disabled/1/2/3/4/5/6

Relay function:

Normally Open / N.O
Normally Closed / N.C

Alarm 1/2/3/4

System
Setup
Setup - Controller
pH control:

On/Off

Enables or disables the disinfection con-
troller (only to be used for constant flow
application)

Conductivity control:

On/Off

Disabled or enabled the conductivity
control function

Setup - Measuring
pH:

On/Off

Disabled or enabled the pH measure-
ment and control function

ORP:

On/Off

Disabled or enabled the ORP measure-
ment function (only by installed sensor
measuring module redox)

Conductivity:

On/Off

Disabled or enabled the conductivity
measurement function (only by installed
sensor measuring module conductivity)

Gerneral information
System name:

Freely definable

Language:

German/English/French/Italian/

Croatian/Dutch/Japanese

«
...
55
56
57
58
59
...
»

Содержание DEPOLOX POOL COMPACT WALLACE & TIERNAN

























































































Отзывы:

Нет отзывов

Похожие инструкции для DEPOLOX POOL COMPACT WALLACE & TIERNAN

Бренд: WAGER Страницы: 22

Бренд: Van Walt Страницы: 6

Бренд: zebris Страницы: 42

Бренд: OHAUS Страницы: 26

Бренд: IFR Страницы: 46

Бренд: Lasertec Страницы: 21

Бренд: CONDTROL Страницы: 8

Бренд: Solartron Mobrey Страницы: 34

Бренд: Bahco Страницы: 21

Бренд: Kübler Страницы: 72

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: B meters Страницы: 3

AirCon Service Mini Identifier R-1234yf

Бренд: Waeco Страницы: 132

Бренд: Keithley Страницы: 338

Бренд: ZIEHL Страницы: 37

Бренд: XPOtool Страницы: 6

Бренд: Simex Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды