E2608 series Modbus holding registers (part 3)
Register addresses are shown 0-based, Addr in hexadecimal, Reg in decimal format.
Modbus holding register numbers MHR are shown in decimal 1-based format, and may be addressed either from 00001 or 40001 base.
Addr
Reg / MHR RW
Description
Supported values (dec)
Default
0x00DB
219 / 40220 RW
Control logic for relay RE1
0 – none
1 – relay on at high values
2 – relay on at low values
3 – relay on at values within the range
4 – relay on for the values out of the range
0
0x00DC
220 / 40221 RW
Control logic for relay RE2
0 – none
1 – relay on at high values
2 – relay on at low values
3 – relay on at values within the range
4 – relay on for the values out of the range
0
0x00DD
221 / 40222 RW
LOW setpoint for relay RE1
0...65535 (gas units)
see
Specifications
0x00DE
222 / 40223 RW
HIGH setpoint for relay RE1
0...65535 (gas units)
see
Specifications
0x00DF
223 / 40224 RW
LOW setpoint for relay RE2
0...65535 (gas units)
see
Specifications
0x00E0
224 / 40225 RW
HIGH setpoint for relay RE2
0...65535 (gas units)
see
Specifications
0x00FF
255 / 40256 RW
Sensor, analog outputs, LED and buzzer status
bit[0]=0/1 – sensor present/absent, read-only!
bit[1]=0/1 – analog outputs deactivated/activated,
bit[2]=0/1 – in case the sensor is absent, turn signaling off/on analog output1,
bit[3]=0/1 – in case the sensor is absent, turn on signaling with low current/high
current on analog output1; if bit[2]==0 this bit will be ignored
bit[4]=0/1 – in case of sensor absent, turn signaling off/on analog output2
bit[5]=0/1 – in case of sensor absent, turn on signaling with low current/high current
on analog output2; if bit[4]==0 this bit will be ignored
bit[6]=0/1 – current/voltage output detected on output1, read-only!
bit[7]=0/1 – current/voltage output detected on output2, read-only!
bit[8]=0/1 – LED deactivated/activated
bit[9]=0/1 – buzzer deactivated/activated
bit[10]=0/1 – LED is on/off in normal condition
bit[11]=0/1 - 1 Hz (50% on, 50% off) LED signal off/on if relay1 turned on
bit[12]=0/1 - 2 Hz (50% on, 50% off) LED signal off/on if relay2 turned on
user defined
0x0100
256 / 40257
R
Raw temperature data, °C×100
signed integer, -4000...+8500 (-40,00...+85,00 °C)
0x0101
257 / 40258
R
Raw gas sensor data
ADC data 0...4095
0x0102
258 / 40259
R
Measured temperature, °C×100
signed integer, -4000...+12500 (-40,00...+125,00 °C)
0x0103
259 / 40260
R
Gas concentration, gas units
0...65535, gas units
0x0105
261 / 40262 RW
0% value for analog output 1
signed integer, -32000...+32000 (ppm / ‰)
0
0x0106
262 / 40263 RW
100% value for analog output 1
signed integer, -32000...+32000 (ppm / ‰)
1000
0x0107
263 / 40264 RW
0% value for analog output 2
signed integer, -32000...+32000 (ppm / ‰)
0
0x0108
264 / 40265 RW
100% value for analog output 2
signed integer, -32000...+32000 (ppm / ‰)
1000
* — The new value is applied after restart.
** — Broadcast slave ID 0 can be used to assign a new ID to device with unknown ID. When addressing by ID 0 the device shall be the only Modbus instrument in the network.
The device will not respond to Master command when addressed by ID 0.
*** — This value is dynamic and not kept in EEPROM after restart
NOTE 2
Sensor absense signalling (bits from [2] to [5]) is available only
for sensors with digital interface ( e.g.-CO2 10K, -O2-L).
NOTE 3
LED/buzzer signalization (if activated):
Detectable sensor
absence or malfunction
0.5Hz (90% off, 10% on) light and/or sound
signal
Relay1 turned on
1 Hz (50% on, 50% off) light and/or sound
signal, depending on bit[8], bit[9] and bit[11]
Relay2 turned on
2 Hz (50% on, 50% off) light and/or sound
signal, depending on bit[8], bit[9] and bit[12]
Modbus response
the light signal is modulated with short on-off
pulses, even single Modbus cycle is visible
Normal operating
continuously on/off depending on bit[10]
NOTE 4
We recommend to set the difference between the upper and
bottom limits of the output scale not narrower than 20% of detection
range (for CO detectors the scales down to 5% of range are allowed). In
any case, do not set the output scale below the tenfold resolution of the
device.
NOTE 1
Relay setpoints should be set within 5-95% of the detection
range.
