background image

Installing the CPU 

Be very careful when handling the CPU. Hold the processor only by the edges and do not 
touch the bottom of the processor. 
Use the following procedure to install the CPU onto the 
motherboard. 
1.

 

Unhook the socket lever by pushing 

down

 and 

away

 from the 

socket.  

2.

 

Lift the load plate. There is a protective socket cover on the 
load plate to protect the socket when there is no CPU 
installed.  

3.

 

Remove the protective socket cover from the load plate.  

4.

 

Remove the processor from its protective cover, making sure 

you hold it only by the edges.  
It is a good idea to save the cover so that whenever you 
remove the CPU, you have a safe place to store it. 

5.

 

Align the notches in the processor with the notches on the 

socket.  

6.

 

Lower the processor straight down into the socket with out 

tilting or sliding it into the socket 

Note:

 

Make sure the CPU is fully seated and level in the socket. 

7.

 

Close the load plate over the CPU and press down while you 

close and engage the socket lever.  

Installing the CPU heat sink/fan 

There are many different heat sink types that can be used with this motherboard. Follow the 
instruction that came with your fan assembly. Be sure that the fan orientation is correct for 
your chassis type and your fan assembly. 

Installing Memory DIMMs 

Your new motherboard has two 1.8V 240-pin slots for DDR2 memory. These slots support 
256 MB, 512 MB, 1 GB, and 2 GB DDR2 technologies. There must be at least one memory 
bank populated to ensure normal operation.  
*Any of the two DIMM slots may be used as primary if only using one memory module.    
1.

 

Unlock a DIMM slot by pressing the module clips outward. 

2.

 

Align the memory module to the DIMM slot, and insert the module vertically into the 

DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock the 
DIMM into the connector.  

Installing the Motherboard 

The sequence of installing the motherboard into the chassis depends on the chassis you are 
using and if you are replacing an existing motherboard or working with an empty chassis. 

Align notches with 
notches on the CPU

Содержание 112-CK-NF72-K1


















Отзывы: