evertz VistaLINK 7700 MultiFrame Скачать руководство пользователя страница 17

Страница: 17 / 22

7700 MultiFrame Manual

7707OO-2-OC Telecom and Datacom Optical Wavelength Converter

Revision

1.3

Page-13

4.2.6. Selecting the Data Standard Mode

The data rates reclocked by the 7707OO-2-OC are grouped into Telecom and Datacom categories as
follows:

Standard Data

Rate

Telecom

OC48/STM16 2.488

Gb/s

OC12/STM4 622

Mb/s

OC3/STM1 155

Mb/s

Gigabit Ethernet

1.25 Gb/s

Datacom

Fiber Channel

2.125 Gb/s

Fiber Channel

1.062 Gb/s

Fiber Channel

531 Mb/s

Fiber Channel

266 Mb/s

Fiber Channel

133 Mb/s

Fast Ethernet

125 Mb/s

XAUI 3.125

Gb/s

XAUI 3.187

Gb/s

ESCON 200

Mb/s

The 7707OO-2-OC should be set for either Telecom or Datacom mode as appropriate for the incoming
signals. To set the data mode, select the

CTRL

menu item in menu level 1, then use the toggle switch to

display the

MODE

option

and press the pushbutton to select it.

CTRL

MODE

TCOM
DCOM

TCOM

Telecom Rates

DCOM

Datacom Rates

4.2.7. Setting the Data Standard

For proper operation, the 7707OO-2-OC must be configured to support the incoming signal type. Telecom
data rates (see section 4.2.6) may be automatically detected and reclocked or a specific rate may be
manually selected. Datacom data rates (see section 4.2.6) must be manually selected. In both modes, a
reclocker bypass option is available for signal types/rates that are not listed. To select a particular data
rate, select the

CTRL

menu item in menu level 1, and then use the toggle switch to display the

RATE

option

and press the pushbutton to select it.

CTRL

RATE

TCOM

OC48-2488MBPS
OC12-622MBPS
OC3-155MBPS
ETH-1250MBPS
AUTO
BYP

OC48-2488MBPS

OC48/STM16, 2.488 Gb/s

OC12-622MBPS

OC-12/STM-4, 622 Mb/s

OC3-155MBPS

OC-3/STM-1, 155 Mb/s

ETH-1250MBPS

Gigabit

Ethernet

AUTO

Rate is automatically detected and reclocked

BYP

Reclocker is bypassed

Содержание VistaLINK 7700 MultiFrame























Результаты поиска

Содержание VistaLINK 7700 MultiFrame

Отзывы:

Похожие инструкции для VistaLINK 7700 MultiFrame

Бренды по названию

Популярные бренды

evertz VistaLINK 7700 MultiFrame, Руководство пользователя

Результаты поиска

Содержание VistaLINK 7700 MultiFrame

Отзывы:

Похожие инструкции для VistaLINK 7700 MultiFrame

Бренды по названию

Популярные бренды