manualshive.com logo in svg

evertz 7847FSEDA Series, Руководство пользователя

Поделиться
Скачать
evertz 7847FSEDA Series Скачать руководство пользователя страница 59

7847FSEDA Series  

Frame Synchronizer and Distribution Amplifier 

 

 

Revision 0.1

 

Page - 49

 

Module & Channel Select: 

These option buttons allow the user to toggle between configuration of 

IntelliGain

® 

Module 1 & 2 and input channel mixers 1-4 and 5-8. 

 

Source – X & Y: 

These controls allow the user to route one of the selectable mixer input audio sources 

to the corresponding input (X or Y) of the IntelliGain

® 

input channel mixer. 

 
Gain – X & Y: 

These controls allow the user to set the value of the gain for the mixer input channel (X 

or Y). The user can adjust the gain of the selected mixer channel (X or Y) by adjusting the 
corresponding slider control. The supported range for gain adjustments is 

-24dB to +24dB

. The gain 

can be adjusted with 

0.1dB

 precision. 

 

Inversion – X & Y: 

These controls allow the user to invert the phase (180 degree phase shift) of the 

corresponding mixer input channel. By selecting 

Normal, 

the module will pass the mixer input audio 

through with no processing. By selecting 

Invert, 

the module will invert the  phase of the mixer input 

audio channel (X or Y). 
 

5.2.14.2. IntelliGain

®

 Configuration [+IG2] 

The IntelliGain

®

  Configuration tab contains the global configuration controls for the IntelliGain audio 

processing module. Figure  5-22  illustrates the layout of these controls in the VistaLINK® PRO 
configuration view.  The specific functionality of each control is provided below. 
 

 

Figure 5-20: Video Path Configuration - IntelliGain

®

 Configuration Tab 

 

Global Configuration 

Compander Attack Time: 

 This control allows the user to set how quickly the compander reacts to 

an increase in the input loudness. The value range is 10 ms to 2000 ms (2 sec). 
 

Compander Release Time: 

This control allows the user to set how quickly the compander reacts to a 

decrease in the input loudness. The compander release time should be greater than or equal to the 

Compander Attack Time

. The value range is 10 ms to 2000 ms (2 sec). 

 

Leveler Attack Mode: 

This control allows the user to set the maximum integration time that is applied 

when loudness decreases during a program period. The actual integration time is content dependent.  
For more responsive results, set the attack time to a smaller value.  The value range is 1 (most 
responsive) to 12 (least responsive) 
  

Input Loudness Mode: 

This control allows the user to set the window that will be used to produce 

the 

Input Loudness.  

 

Содержание 7847FSEDA Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды