evertz 7847FSEDA Series Скачать руководство пользователя страница 21

Страница: 21 / 86

7847FSEDA Series

Frame Synchronizer and Distribution Amplifier

Revision 0.1

Page - 11

STATUS LEDS

4.1.

MODULE STATUS LEDS

Figure 4-1 depicts status LEDs for the 7847FSEDA series modules. LEDs are in the same position
and perform the same function as the 7815VPDA and 7815IDA series modules.

7847FSEDA

Shaft

Encoder

(not used)

Module

Status

SDI

PGM IN 2

SDI

PGM IN 1

FIBER

IN 1

FIBER

IN 2

REFERNCE

AUDIO

IN 1

AUDIO

IN 2

COOLING

FANS

Local

Fault

Figure 4-1: 7847FSEDA Status LEDs

MODULE STATUS:

This Green MODULE STATUS LED will be ON when the module has valid
video on one of its inputs.

LOCAL FAULT:

This Red LOCAL FAULT LED will be ON when no valid video standard is
detected on both input video paths.

SDI PGM IN 1:

The SDI PGM IN 1 LED will be GREEN when a valid input standard is
detected on SDI PGM IN for video path 1. OFF otherwise.

FIBER IN 1:

The FIBER IN 1 LED will be GREEN when a valid input standard is detected
on FIBER IN for video path 1. OFF otherwise.

SDI PGM IN 2:

The SDI PGM IN 2 LED will be GREEN when a valid input standard is
detected on SDI PGM IN for video path 2. OFF otherwise.

FIBER IN 2:

The FIBER IN 2 LED will be GREEN when a valid input standard is detected
on FIBER IN for video path 2. OFF otherwise.

REFERENCE:

The REFERENCE LED will be GREEN when a valid reference video
standard is detected. OFF otherwise.

AUDIO IN 1:

The AUDIO IN 1 LED will be GREEN when embedded audio group 1 is
present on the input video standard signal processed by video path 1. OFF
otherwise.

AUDIO IN 2:

The AUDIO IN 2 LED will be GREEN when embedded audio group 1 is
present on the input video standard signal processed by video path 2. OFF
otherwise.

COOLING FANS

The COOLING FANS LED will be GREEN when both cooling fans are
operating properly. OFF when either fan, or both fans are in error.

Содержание 7847FSEDA Series























































































Результаты поиска

Содержание 7847FSEDA Series

Отзывы:

Бренды по названию

Популярные бренды

evertz 7847FSEDA Series, Руководство пользователя

Результаты поиска

Содержание 7847FSEDA Series

Отзывы:

Бренды по названию

Популярные бренды