evertz 7814UDX-4K Series Скачать руководство пользователя | Manualshive

Страница: 17 / 64

background image

7814UDX-4K Series

HD/3G/UHD Up/Down/Cross Converters

Revision 1.2

Page - 7

2.2.

ETHERNET CONNECTIONS

All 7814UDX-4K series modules are designed to use either 10Base-T (10 Mbps) or 100Base-TX (100
Mbps) also known as

Fast Ethernet

, twisted pair Ethernet cabling systems. When connecting for 10Base-

T systems, category 3, 4, or 5 UTP cable as well as EIA/TIA – 568-100

Ω

STP cable may be used. When

connecting for 100Base-TX systems, category 5 UTP cable is required. Make the network connection by
plugging one end of a “straight through” cable into the RJ-45 receptacle of 7814UDX-4K modules and the
other end into a port of the supporting hub. If you are connecting the 7814UDX-4K series modules directly
to an Ethernet port on a computer, you will have to use a “crossover” cable.

Straight-through RJ-45 cables can be purchased or can be constructed using the pin out information in
Table

2-2. A color code-wiring table is provided in Table

2-1 for the current RJ-45 standards (AT&T 258A

or EIA/TIA 258B color coding shown). Also, refer to the notes following the table for additional wiring guide
information.

Pin
1

Pin #

Signal

EIA/TIA 568A

AT&T 258A or

EIA/TIA 568B

10BaseT

or 100BaseT

1

Tr

White/Green

White/Orange

X

2

Transmit –

Green/White or White

Orange/White or

Orange

X

3

R

White/Orange

White/Green

X

4

N/A

Blue/White or Blue

Blue/White or Blue

Not used

(required)

5

N/A

White/Blue

White/Blue

Not used

(required)

6

Receive –

Orange/White or Orange

Green/White or Green

X

7

N/A

White/Brown

White/Brown

Not used

(required)

8

N/A

Brown/White or Brown

Brown/White or Brown

Not used

(required)

Table

2-1 : Colour Code Wiring for the Current RJ 45 Standards

Note the following cabling information for this wiring guide:

•

Only two pairs of wires are used in the 8-pin RJ 45 connector to carry Ethernet signals.

•

Even though pins 4, 5, 7 and 8 are not used, it is mandatory that they be present in the cable.

•

10BaseT and 100BaseT use the same pins; a crossover cable made for one will work with the
other.

•

Pairs may be solid colors and not have a stripe.

•

Category 5 cables must use Category 5 rated connectors.

The maximum cable run between the 7814UDX-4K series modules and the supporting hub is
300 ft (90 m).

«
...
15
16
17
18
19
...
»

Содержание 7814UDX-4K Series

































































Отзывы:

Нет отзывов

Похожие инструкции для 7814UDX-4K Series

Бренд: Parkside Страницы: 77

Бренд: Parkside Страницы: 65

Бренд: QUAD Страницы: 2

Бренд: Olimpia splendid Страницы: 144

Бренд: National Instruments Страницы: 411

Бренд: Autarco Страницы: 37

Бренд: B&B Electronics Страницы: 2

Бренд: tams elektronik Страницы: 39

Бренд: Clarke Страницы: 36

Бренд: WarmPool Страницы: 37

Бренд: ADF Web Страницы: 17

Бренд: ADF Web Страницы: 20

Бренд: ADF Web Страницы: 19

Бренд: ADF Web Страницы: 18

Бренд: ADF Web Страницы: 30

Бренд: ADF Web Страницы: 30

Бренд: ADF Web Страницы: 30

AXIS HD67611-A1

Бренд: ADF Web Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды