evertz 7707BPX Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

7700 MultiFrame Manual

7707BPX Optical Bypass Protection Switch

Revision

1.6

Page-5

2. INSTALLATION

The 7707BPX comes with a companion rear plate that has three SC/PC (shown), ST/PC or FC/PC optical
connectors and a six pin terminal strip. For information on mounting the rear plate and inserting the
module into the frame see the 7700FR chapter section 3.

Figure 2-1: 7707BPX Rear Panel

INPUT A, B:

The two SC/PC, (shown), ST/PC or FC/PC female connectors are wide range optical inputs
that accept wavelengths accommodating standard 1310nm, or 1270nm to 1610nm CWDM
transmission schemes. The A connector is for the

Main

input and the B connector is for the

Standby

input.

OUTPUT:

This SC/PC, (shown), ST/PC or FC/PC female connector is the output from the switch.

«
...
7
8
9
10
11
...
»

Содержание 7707BPX

























Отзывы:

Нет отзывов

Похожие инструкции для 7707BPX

Бренд: GAIM Страницы: 2

Бренд: Camozzi Страницы: 2

COOPER POWER SERIES

Бренд: Eaton Страницы: 24

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

Crouse-hinds series

Бренд: Eaton Страницы: 16

Cutler-Hammer AMPGARD

Бренд: Eaton Страницы: 4

Raritan Dominion LX II

Бренд: LEGRAND Страницы: 7

Бренд: ATEN Страницы: 2

Бренд: Velleman Страницы: 5

Бренд: Eaton Страницы: 120

Бренд: Vega Страницы: 44

Бренд: Crestron Страницы: 36

Бренд: MLis Страницы: 85

Бренд: ATEN Страницы: 261

SUPERHUB QUATTRO

Бренд: Manhattan Страницы: 2

PSEN ma2.1p/ATEX

Бренд: Pilz Страницы: 8

Бренд: DataParts Страницы: 4

Бренд: Pliant Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды