evertz 5782ENC-H264HD-IPASI Скачать руководство пользователя | Manualshive

Страница: 16 / 62

background image

5782ENC-H264HD-IPASI

Professional Contribution H.264 and MPEG-2 Encoder

Page - 6

Revision 1.0

3.3.

HARDWARE INSTALLATION

3.3.1. Three Different Ways to Control and Configure the 5782ENC-H264HD-IPASI

There are two different ways that 5782ENC can be controlled and configured:

1. WebEASY

®

using the 570FC frame controller with 5782ENC-H264HD-IPASI installed in frame.

2. VistaLINK

®

using the 570FC frame controller with 5782ENC-H264HD-IPASI installed in frame.

3.3.2. Module Installation

Before handling the card it is important to minimize the potential effects of static electricity. It is
therefore recommended that an ESD strap be worn.

Locate on the 570FR frame chassis one adjacent vacant slot. Unpack the 5782ENC-H264-HD-IPASI
and separate the rear plate module from the main card. Locate on the rear of the rack the one slot and
remove the blanking panel. Insert the rear plate module into the back of the chassis and secure using
the two screws provided.

Figure 3-2: 570FR Chassis

Insert the 5782ENC-H264HD-IPASI card into the corresponding front slots ensuring the card lines up
with the slot runners on the bottom and the top of the chassis. Push the card into the slot ensuring that
when it mates with the rear card that is has been firmly pushed into a seated position. Use the thumb
screw to properly secure the module.

Do not over tighten thumb screws.

«
...
14
15
16
17
18
...
»

Содержание 5782ENC-H264HD-IPASI































































Отзывы:

Нет отзывов

Похожие инструкции для 5782ENC-H264HD-IPASI

Бренд: WALKMAN Страницы: 6

Бренд: Barco Страницы: 2

Бренд: HANYOUNG NUX Страницы: 2

Бренд: DAAB Страницы: 8

Бренд: Chemtronics Страницы: 20

Бренд: EtherWAN Страницы: 13

Бренд: Rayleigh Instruments Страницы: 27

Бренд: ADF Web Страницы: 36

Бренд: ifi Страницы: 2

Бренд: Renkforce Страницы: 4

Бренд: Barco Страницы: 2

blueplanet 3.0 TL1

Бренд: Kaco Страницы: 56

CC15-xxxx-Sxx-E Series

Бренд: TDK-Lambda Страницы: 11

Бренд: Zling Страницы: 12

Бренд: ENFORCER Страницы: 4

Бренд: AJA Страницы: 43

Бренд: Data Connect Страницы: 32

Бренд: Mayty Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды