evertz 570NAT-HW-X19 Скачать руководство пользователя страница 35

Страница: 35 / 56

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 25

4.4.1. LAN to WAN: Input Configuration

Flows 1 to 256

Mode:

This control allows the user to enable the associated input stream for encapsulation.

VLAN ID:

This control allows the user to assign a VLAN ID to the associated flow; incoming packets of

the flow with the specified VLAN ID will then be encapsulated.

Input Bit rate:

This monitor will display the bit rate coming in on the port

4.4.2. LAN to WAN: Encapsulation Header Configuration

Flows 1 to 256

Source IP Address:

This control allows the user to set the physical source IP address of the incoming

streams.

Source UDP Port:

This control allows the user to set the physical source UDP port of the incoming

streams.

Destination IP Address:

This control is used to configure the output header encapsulation with the

desired destination IP address.

Destination UDP Port:

This control is used to configure the output header encapsulation with the

desired destination UDP Port number.

4.4.3. WAN to LAN: De-Encapsulation Configuration

Flows 1 to 256

Mode:

This control allows the user to enable the associated input stream which is going to be de-

encapsulated.

Input Destination IP Address:

This control allows the user to set the IP address of the packet to be

received for de-encapsulation.

Input Destination UDP Port:

This control allows the user to set the UDP Port number to be received

for de-encapsulation.

Input Bit rate:

This monitor will display the bit rate coming in on the port

Содержание 570NAT-HW-X19

























































Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды

evertz 570NAT-HW-X19, Руководство пользователя

Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды