manualshive.com logo in svg

evertz 570EMR-AG-HUB, Руководство пользователя

Поделиться
Скачать
evertz 570EMR-AG-HUB Скачать руководство пользователя страница 21

570EMR-AG-HUB 

User Manual

 

 

 

Revision 0.1

 

Page - 11 

5.1.1.  Control Port Configuration 

Ethernet:

 Allows the user to set the IP Address, Netmask and Gateway. This IP Address is used for 

control and monitor, when 570EMR in standalone frame. 

Proxy: 

This

 

IP Address is received from 570FC through proxy. Doesn’t allow the user to change the IP 

in 570EMR webpage but user can change the IP Address in 570FC Software tab page. This IP address 
is used for control and monitor when 570EMR in 570 Frame with 570FC. 

 

5.1.2.  Data Port Configuration 

Only 8 SFPs are currently available and the user can set the following parameters on each SFPs. Make 
sure SFP’s data ports must have different subnet IP address. 
 

IP Address:

 This parameter allows the user to set the IP Address for the data port. 

NetMask:

 This parameter allows the user to set the Netmask for the data port. 

Gateway:

 This parameter allows the user to set the gateway for the data port. 

 

5.1.3.  Data Port Monitor 

This section allows the user to monitor the following parameters on each SFP’s. 
 

Ethernet Rx Bandwidth:

 Displays the Received Ethernet Bandwidth displayed in Mbps. 

Ethernet Rx Frames Ok: 

Displays the number of Error-Free Frames Received. 

Ethernet Rx Frames Err:

 Displays the number of Erroneous Frames Received. 

Ethernet Rx Broadcast Frames: 

Displays the number of Broadcast Frames Received. 

Ethernet Rx Unicast Frames: 

Displays the number of Unicast Frames Received. 

Ethernet Rx MultiCast Frames: 

Displays the number of Multicast Frames Received. 

Ethernet Tx Bandwidth: 

Displays the Transmitted Ethernet Bandwidth displayed in Mbps. 

Ethernet Tx Frames Ok: 

Displays the number of Error-free Frames Transmitted. 

Ethernet Tx Frames Err: 

Displays the number of Erroneous Frames Transmitted. 

Ethernet Tx Broadcast Frames: 

Displays the number of Broadcast Frames Transmitted. 

Ethernet Tx Unicast Frames: 

Displays the number of Unicast Frames Transmitted. 

Ethernet Tx MultiCast Frames: 

Displays the number of Multicast Frames Transmitted. 

Ethernet Link Status: 

Displays the Ethernet port link status as either up or down. 

Clear Stats: 

Allows the user to clear the Stats recorded above by pushing the button.

  

 

5.1.4.  SFP Control 

SFP Detection:

 This control allows the user to specify the type of cable used with the SFP. Options are 

Auto, Optical, Copper 3m and Copper 5m. 
 

Содержание 570EMR-AG-HUB



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды