Command Classes
The module supports Command Classes including…
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SWITCH_BINARY
*
COMMAND_CLASS_SWITCH_ALL
*
COMMAND_CLASS_ASSOCIATION_V2
*
COMMAND_CLASS_ASSOCIATION_GRP_INFO
*
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_VERSION_V2
*
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
*
COMMAND_CLASS_DEVICE_RESET_LOCALLY
*
COMMAND_CLASS_POWERLEVEL
*
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_NOTIFICATION_V8
*
COMMAND_CLASS_CONFIGURATION_V2
*
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
*
*Items marked an asterisk are secure command classes.
Troubleshooting
The table below lists the several steps involved when adding or removing the unit from the Z-Wave
network.
Action/Status
Description
LED indication
No node ID Status
The unit has not been added to the Z-Wave
network.
2-second on, 2-second
off
Auto Inclusion
Inclusion starts immediately when power is applied
for the first time. (This occurs only if no node ID is
stored in the module, usually after Exclusion or after
executing a Factory Reset).
Manual Inclusion
1. Put the Z-Wave Controller into
Inclusion mode.
2. Press the On/Off knob 3 times within 1.5 seconds
to put the unit into Inclusion mode.
Exclusion
1. Put the Z-Wave Controller into Exclusion mode.
2. Press the On/Off knob 3 times within 1.5 seconds
to put the unit into Exclusion mode.
Factory Reset
(This procedure
should only be
used when the
controller is
inoperable.)
1. Press the On/Off knob 3 times within 1.5 seconds
to put the unit into exclusion mode.
2. Within 1 second of step 1, press and hold the
knob for 5 seconds.
3. Node ID is deleted. The device reverts to factory
default state.
2-second on, 2-second
off
Failure or success in including/excluding the ID can be viewed on the Z-Wave Controller.
Table below lists typical problems encountered:
Symptom
Cause of Failure
Recommendation
The unit is not working and
LED is always off even when
knob is pressed
The unit is not plugged into the
electrical outlet properly
Check power connections to the
unit.
The unit’s LED turns on but
connected appliance does not
turn on.
1. The connected appliance has its
own power switch set to off.
1. Set the ON/OFF switch of the
appliance itself to ON position.
2. The appliance requires a separate
remote control to turn.
2. Appliances turned on/off by with
remote control cannot be controlled
by this On/Off plug module.
The module works if operated
manually but cannot be
controlled wirelessly by end
devices in Group 2 mode.
1. Z-Wave Association process was
not implemented.
2. Frequency interference
3. Out of range
1. Carry out Z-Wave Association.
2. Wait for a while to re-try
3. Move the device or module
closer to each other.
Specification
Operating Voltage
AC100-120V, 50/60Hz
Maximum Load
1400W
Range
Up to 100 meters line of sight
Frequency Range
US: 908.42 MHz
JP: 922.5MHz
FCC ID
FU5AN186
IC
23210-AN186
* Specifications are subject to change without notice.
Mobile of end product
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
