- 1 -
AN180
Z-Wave On/Off Mini Plug
The On/Off Mini Plug is a Z-Wave
TM
enabled device which is fully compatible with any Z-Wave
TM
enabled
network. Z-Wave
TM
enabled devices displaying the Z-Wave
TM
logo can also be used with it regardless of
the manufacturer, and ours can also be used in other manufacturer’s Z-Wave
TM
enabled networks.
Inclusion of this unit on other manufacturer’s Wireless Controller menu allows remote operation of the unit
and the connected load.
The On/Off Mini Plug is designed to control the on/off status of lighting and appliances load in your house.
At 220-240V voltage, this Plug can support up to 1500W resistive, 800W incandescent, 200W motor, or
200W fluorescent load.
Product Overview
Adding to Z-Wave
TM
Network
On the unit you can find a link key which is used to carry out the function of inclusion, exclusion, and reset.
When power is applied for the first time, the LED will flash on and off alternately and repeatedly, implying that
it has not been assigned a node ID and cannot work with other Z-Wave devices yet. This unit supports the
Auto Inclusion function when power is applied and no node ID is stored in the memory.
Auto Inclusion
The module may automatically execute the function of inclusion when...
1. The power is applied for the first time and no node ID has been stored in the module.
2. The execution of reset is successful where the stored node ID is cleared.
Note:
The duration for Auto Inclusion is about 4 minutes. Unlike the “inclusion” procedure shown in the
table below, the execution of Auto Inclusion is automatic without the necessity of pressing the link key.
Action/Status
Description
LED indication
No node ID
The Controller does not allocate a node ID to the unit.
2-second on,
2-second off
Auto Inclusion
The power is applied for the first time and no node ID has
been stored in the module, or after executing reset.
Inclusion
1. Put the Z-Wave Controller into inclusion mode.
2. Press the link key three times within 1.5 seconds to put
the unit into inclusion mode.
Exclusion
1. Put the Z-Wave Controller into exclusion mode.
2. Press the link key three times within 1.5 seconds to put
the unit into exclusion mode.
Reset
(This procedure
should only be used
when the network
primary controller is
inoperable.)
1. Press the link key three times within 1.5 seconds to put
the unit into exclusion mode.
2. Within 1 second of step 1, press link key again and
hold it until LED is off (about 5 seconds).
3. Node ID is excluded. The device reverts to factory
default state and will be in auto-inclusion mode for 4
minutes.
Failed or successful results in including/excluding the node ID can be viewed on the Controller.
Operation
Under normal operation mode, press the on/off button on the unit to control the on/off status of the connected
load. When power is on, the LED indicator will turn on for 5 seconds and then turn off (or slow flash if no
node ID is stored). The unit can also be controlled by receiving command signals from the Z-Wave
Controller.
The unit is able to remember the status of the relay when power is cut off (such as power black-out). When
power is supplied again, the unit will resume the last status of the relay (on or off) automatically.
Programming
Z-Wave Group Support
The unit supports two association groups with 1 node support for Grouping 1 and 4 nodes support for
Grouping 2. This has the effect that when the unit is operating, all devices associated with the unit will
receive the relevant reports.
When the unit is powered for the first time, the unit will send a Notification Report to the node of Group 1.
When setting the unit or changing the unit’s status, the unit will send a Binary Switch Report to the node
of Group 1.
Device Reset: When performing Reset the unit will send Device Reset Locally Notification to the node of
Group1.
The minimum interval time between two reports sent from this unit to the node of Group 1 is 3 seconds.
Refer to
Configuration
parameter 2 for more information.
When the button on the unit or the wall switch is pressed, the unit will send a Basic Set command to the
nodes of Group 2. When the unit is OFF, Basic Set Value = 0x00. When the unit is ON, Basic Set
Value = 0xFF.
Z-Wave Plus Info
Role Type
Node Type
Installer Icon
User Icon
Slave Always On
Z-Wave Plus node
On/Off Power Switch
On/Off Power Switch
Version
Protocol Library
3 (Slave_Enhance_232_Library)
Protocol Version
3.95 ( 6.51.02)
Firmware 0 Version
1V1
Hardware Version
2
Firmware 1 Version
0V4
On/Off Button
& Link Key
(with LED light)
