manualshive.com logo in svg

EverFocus EZ650, Инструкция по эксплуатации

Поделиться
Скачать
EverFocus EZ650 Скачать руководство пользователя страница 22

 

 

21 

3. OSD Menu & Configuration 

This chapter introduces how to configure the camera OSD menu. 
 

3.1 Control Key General Operation Guide 

 
Please turn the control key selection switch at the back panel to “

OSD

” ”(        ). 

Use the control key to do OSD menu setting. 

 
 

 

 
 

 
 

 
 

 
 
 
 
 

I.

 

Bring Up the General OSD Menu  

Simply press the mini-joystick to bring up the general OSD menu. 

 

 

II.

 

Bring up the RS485 Setting Menu  

Press the mini-joystick and hold for 5 seconds to bring up the RS485 setting menu. 
 

III.

 

Navigate among the OSD Menu Items 

Turn the mini-joystick up (

) or down (

) to move the cursor up or down.  

 

IV.

 

Change Modes or Setting Parameters 

Turn the mini-joystick left (

) or right (

) to adjust the mode or parameter of settings. 

 

V.

 

Switch to Sub-menu Screens 

Chapter 

3 

The Cursors & the mini-joystick 

Mini-Joystick 

UP 

Содержание EZ650









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды