manualshive.com logo in svg

EUTECH INSTRUMENTS alpha-pH 2000D, Инструкция по эксплуатации, Страница: 33 / 50

Поделиться
Скачать
EUTECH INSTRUMENTS alpha-pH 2000D Скачать руководство пользователя страница 33

Instruction Manual 

 

α

lpha-pH2000D 

 

- 28 - 

 

6.8

 

Wash relay (WASH) sub-function  

 
In this sub-function you set the parameters for the wash relay.  
 

1

2

2

3

3

4

5

ENT

ENT

ENT

ENT

ENT

ENT

ENT

SETUP

HOLD

SETUP

HOLD

SETUP

HOLD

SETUP

HOLD

SETUP

HOLD

SETUP

HOLD

SETUP

HOLD

off

 

 

1.

 

Select the “WASH” sub-function, and then press the ENT key.  

2.

 

Enabling/disabling wash function: press the 

▲

 or 

▼

 key to enable (WASH ON) or disable 

(WASH OFF) wash function. Press the ENT key to confirm your selection.  

3.

 

Selecting the relay status condition: press the 

▲

 or 

▼

 key to choose desired relay status 

(de-energized = “DEEN” or energized = “EN”). Press the ENT key to confirm your selection.  

4.

 

Setting the wash interval in hours: Press the 

▲

 or 

▼

 key to set the desired wash interval 

(setting range: 0.1 to 200.0 hours). Press the ENT key to confirm your setting.  

5.

 

Setting the wash duration in seconds: Press the 

▲

 or 

▼

 key to set the desired wash 

duration (setting range: 1 to 2000 seconds). Press the ENT key to confirm your setting.  

 

 

Note:  During wash cycle the transmitter is set to HOLD. For safety reasons, the 
HOLD function is activated 5 seconds prior and deactivated 10 seconds after the 

wash cycle. 

 
Continue with Setup mode procedures, or return to Measurement mode by pressing the 

▲

 

and 

▼

 keys simultaneously (escape).  

 
 

 

Содержание alpha-pH 2000D



















































Отзывы:

Нет отзывов