background image

Important user information 

 

 

5

Use an appropriate power supply 

Only start the product with a power supply that conforms to the voltage requirements as displayed on 
the voltage label attached to the system. In case of uncertainty about the required power supply, 
please contact your local 

Eurotech Technical Support Team

 (see page 

6

) or the electricity authority. 

Use power supplies that are compliant with SELV regulation. 

Use certified power cables. The power cable must fit the product, the voltage and the required current. 

Position cable with care, Avoid positioning cables in places where they may be trampled on or 
compressed by objects placed on it. Take particular care of the plug, power-point and outlet of power 
cable. 

Avoid overcharging power-points. 

Antistatic precautions 

To avoid damage caused by ESD (Electro Static Discharge), always use appropriate antistatic 
precautions when handing any electronic equipment. 

Life support policy 

Eurotech products are not authorized for use as critical components in life support devices or systems 
without the express written approval of Eurotech. 

CE notice 

The product described in this manual is marked with the 

label in accordance with the 1999/5/EC 

regulation. 

Eurotech shall not be liable for use of its products with equipment (i.e. power supplies, personal 
computers, etc.) that are not CE marked.  

WEEE 

The information below is issued in compliance with the regulations as set out in the 2002/96/EC 
directive, subsequently superseded by 2003/108/EC. It refers electrical and electronic equipment and 
the waste management of such products. 

When disposing of a device, including all of its components, subassemblies and materials that are an 
integral part of the product, you should consider the WEEE directive. 

The symbol to the right has been attached to the equipment or, if this has not been 
possible, on the packaging, instruction literature and/or the guarantee sheet. By using this 
symbol, it states that the device has been marketed after August 13th 2005, and implies 
that you must separate all of its components when possible, and dispose of them in 
accordance with local waste disposal legislations. 

 

Because of the substances present in the equipment, improper use or disposal of the refuse can cause 
damage to human health and to the environment. 

With reference to WEEE, it is compulsory not dispose of the equipment with normal urban refuse, 
arrangements should be instigated for separate collection and disposal. 

Contact your local waste collection body for more detailed recycling information. 

In case of illicit disposal, sanctions will be levied on transgressors. 

Содержание ISIS ICE























Отзывы: