Eurotech EUROLAM Скачать руководство пользователя | Manualshive

Страница: 12 / 19

background image

Start Using the EuroLam

Power on the laminator

Push the rocker switch on the back of the machine case, from ‘0’ to

‘I’. The control panel screen will light up, showing the greeting
words: Welcome.

If the screen fails to light up, please check if any emergency stop

is activated. Just twist the button clockwise to release it. Then the
screen should light up.

Turn the Pneumatic valve to ‘up’ position, the upper roller will lift up

Take off the upper roller hanging hooks

Take off the yellow upper roller hanging hooks on double sides,

this parts designed to protect the rollers in long-term transport by

keep the upper and lower rolls from moving.

The hooks also avoid roller deformation that occurs when the
machine is idle for long periods of time

Up

Down

Middle

«
...
10
11
12
13
14
...
»

Содержание EUROLAM




















Отзывы:

Нет отзывов

Похожие инструкции для EUROLAM

Бренд: 3M Страницы: 3

A3 LAMINATOR ULG300A1

Бренд: UNITED OFFICE Страницы: 11

Бренд: UNITED OFFICE Страницы: 115

Бренд: Rexel Страницы: 21

Бренд: GBC Страницы: 76

Бренд: Click Страницы: 8

Бренд: DSB Страницы: 2

Бренд: DSB Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды