manualshive.com logo in svg

European Home H Series HVF-42-P, Инструкция по установке и эксплуатации, Страница: 23 / 38

Поделиться
Скачать
European Home H Series HVF-42-P Скачать руководство пользователя страница 23

H Series

 Vent Free Gas Fireplace                                                                                                                                                       European

Home

.com

TRIM and FINISH

23

FINISHING THE ENCLOSURE

The 

H Series

 Vent Free Gas Fireplace is designed to be enclosed with common building materials; wood, 

drywall, plaster, etc. 

• 

All materials must be installed within the limits shown previously. 

• 

The facing flanges on these fireplaces are designed for use with 1/2” thick material.  

• 

The wall above the fireplace opening is constantly exposed to elevated temperatures. This must be 

considered when choosing any fasteners, paint, mastic, sealant, caulk, etc., for use in this area as 

materials may change color or emit an odor when heated.  Petroleum-based tile adhesives should be 

avoided and thin-set mortar used instead. 

• 

Facing material should be installed against the outer face of the fireplace, with an 1/8” vertical or 

horizontal clearance 

to the flange

 to allow for heat expansion.

INSTALLING THE FIRE MEDIA

 

Two types of fire media are available for your 

H Series

 Vent Free Gas Fireplace; Fireglass or Carrara Pebbles. 

The Fire Media

The entire contents of the bag of fire media should be spread to an even depth across the entire burner top. 

Be certain that media does not come within 1/4” of the pilot burner.  Media dust should not be emptied on burner 

top as it may clog the gas ports.

The fire media must be installed per these instructions. This heater must use only the fire media provided 

by European Home. An excess amount of fire media may adversely affect the performance of the heater.

WARNING: All previously applied loose material must be removed prior to reapplication.

Содержание H Series HVF-42-P







































Отзывы:

Нет отзывов