To Programme the Timer
Press the ‘P’ button & release it.
Set the day of days that you require the timer to operate from the list already described. The triangles at the top of the screen will show which
days have been selected.
Press the ‘H’ button to set the hour that you want the timer to operate at.
Press the ‘Min’ button to set the minute that you want the timer to operate at.
Press the ‘P’ button again and the OFF time can be set using the same method as setting the ON function just described above.
The timer will return to the master clock screen if no buttons are pressed for 30 seconds.
You have now set one ON/OFF period (#1).
To set additional periods press the ‘P’ button and then again to scroll to period#2 On , then again to #2 OFF and so to #16 if required.
To exit the programme function press the clock button this will return you to the master clock screen.
Enabling the programme to run
Press the ‘Manual’ button and the display will change from ON to ON-AUTO.
Pressing again will move to OFF and subsequent pressing will move to OFF AUTO and then again to ON.
To run the programme the timer needs to be set to either ON-AUTO or AUTO-OFF.
If you are setting the timer to run during a period when the timer is programmed to be off then the AUTO-OFF sheeting needs to be displayed.
If you are setting the timer to run during a period when the timer is programmed to be on the ON-AUTO setting needs to be displayed. IF ON
or OFF are displayed the timer will not operate to the programme set (see manual operation).
Cancelling programme periods
To cancel any programmed ON/OFF period. Press the ‘P’ button repeatedly until the Period number is shown that you wish to cancel or
change. Press the ‘C’ button and the screen will clear.
You will then be able to re-programme this period or leave it blank. Remember to clear both the ON and OFF instructions for any one period.
Resetting the timer clock
Pressing the button marked ’R’ will completely clear the master clock and all programmed periods in the memory of the device.
Manual Operation
Press the manual button to set the device to ON or OFF. This will override any programs that are set and force the timer into the set state ie
ON =on and OFF =off
Calibrating the clock
If the clock is found to be running fast, or slow it is possible to speed it up or slow it down.
Press the ‘Manual’ and ‘P’ buttons at the same time. Then press the ‘D’ button until a number between 0-30 shows this is the number of
seconds to be added in the week. Pressing the ‘D ‘ button again you can scroll until negative numbers are displayed. The negative number
displayed represents the number of seconds by which the clock will be slowed each week.
Countdown Function
It is possible to set the timer so that it counts down from a preset value.
Press the ’P’ and ‘
’ buttons together for 3 seconds
Press the ‘
‘ button and hold down whilst the ‘H’ and ‘M’ buttons are used to set the overall countdown period.
Press the ‘Manual’ button to start
Press the ‘P’ button to stop
Press the ’P’ and ‘
’ buttons together for 3 seconds to exit the countdown function.
Switching the timer off and clearing the menu
Pressing the ‘H’ & ‘Min’ buttons at the same time for ten seconds will switch the timer off. The clock settings and all programmed events will
be cleared. To switch back on press the small ‘R’ button.
ET167DYD
Operating
Instructions
Europa House
Airport Way
Luton, Beds, LU2 9NH
Tel: 01582 692 440 / Fax: 01582 692 450
e-mail: [email protected]
website: http://www.europacomponents.com
Red LED
Illuminated when relay is in ON state
Button ‘P’
Enables Programming
Button ‘D’
Sets the Day
Button ’H’
Sets the Hour
Button ‘Min’
Set the number of minutes
Button ‘ ’
Master clock
Button ‘R’
Resets the device
Button ‘Manual’
Sets the device to ON-AUTO-OFF.
Also cancels out functions.
Guide to Programming Keys
ET167DYD_Instructions:Layout 1 7/11/12 15:30 Page 2
