background image

3 - EN

2 Installation

Removing packaging 

reinforcement

Tilt the machine to remove the packaging 

reinforcement. Remove the packaging 

reinforcement by pulling the ribbon.

Opening the transportation locks

 Transportation safety bolts must be 

removed before operating the washing 

machine! Otherwise, the machine will be 

damaged!

1.  Loosen all the bolts with a spanner until 

they rotate freely (“C”)

2.  Remove transportation safety bolts by 

turning them gently.

3.  Fit the covers (supplied in the bag with the 

Operation Manual) into the holes on the 

rear panel. (“P”)

  

  

 

Keep the transportation safety bolts in 

a safe place to reuse when the washing 

machine needs to be moved again in the 

future.

Never move the appliance without the 

transportation safety bolts properly fixed in 

place!

Adjusting the feet

 Do not use any tools to loosen the lock 

nuts. Otherwise, they can be damaged.

1.  Manually (by hand) loosen the lock nuts on 

the feet.

2.  Adjust them until the machine stands level 

and firmly.

3.  Important: Tighten all lock nuts up again.

Connecting to the water supply.

Important:

•   The water supply pressure required to run 

the machine must be 1-10 bar (0,1 – 1 

MPa).

•   Connect the special hoses supplied with 

the machine to the water intake valves on 

the machine. 

•  If you are going to use your double water-

inlet machine as a single (cold) water-inlet 

unit, you must install the stopper*, supplied 

with your machine to the hot water valve.

•  If you want to use both water inlets of the 

product, you can connect the hot water 

hose after removing the stopper and 

gasket group from the hot water valve.

* Applies for the products supplied with a blind 

stopper group.

•  Models with a single water inlet should not 

be connected to the hot water tap.

When returning the appliance to its place after 

maintenance or cleaning, care should be taken 

not to fold, squeeze or block the hoses.

Connecting to the drain

The water discharge hose can be attached to 

the edge of a washbasin or bathtub. The drain 

hose should be firmly fitted into the drain as to 

not get out of its housing.

Important:

•   The end of the drain hose must be directly 

connected to the wastewater drain or to 

the washbasin.

•   The hose should be attached to a height of 

at least 60 cm, and 90 cm at most.

•   In case the hose is elevated after laying it 

on the floor level or close to the ground 

(less than 40 cm above the ground), water 

discharge becomes more difficult and the 

laundry may come out wet.

•   The hose should be pushed into the 

drainage for more than 15 cm. If it is too 

long you may have it shortened.

•  The maximum length of the combined 

hoses must not be longer than 3.2 m.

90

60

 

 

Содержание WM55

















Отзывы: