PURIFICATION PROCESS
AQUAGUARD
®
NEO UV+UF
UV disinfects the water by eliminating waterborne
disease-causing bacteria, viruses and protozoa,
thereby, making it safe to drink.
i-Filter™
Multi-Layered
Polypropylene Roving
Wound Cartridge
Chemi-Block
(with built-in
Particle Trap
Filter™)
Dust Free
Bacteriostatic
Activated Carbon
Block
Removes fine suspended particles such as dust, dirt,
mud and sand from water.
Reduces excess chlorine, bad odour, colour and
organic impurities. It also removes very fine turbidity
causing particles.
Ultra Filter
UF Hollow Fiber
Capillary tube type membrane-based technology that
imparts crystal clear clarity to drinking water in
addition to making the water safe from bacteriological
contamination.
Germicidal UV Lamp
UV e-boiling
Instantly charges purified water with essential
micro-nutrients like Calcium & Magnesium which
enhance the taste of water & makes it healthier for
consumption.
Calcium &
Magnesium
Enriched Water
Mineral Charge
Cartridge
1.
2.
3.
4.
5.
LED INDICATION CHART FOR
AQUAGUARD
®
NEO UV+UF
Aquaguard
®
Neo UV+UF
Model
2
Dimension (W X D X H)
320 mm x 278 mm x 476 mm
Net Weight
4.5 KG (Approx.)
3
Purification Technology
UV+UF
6.2 Litres (approx.)
4
Tank Capacity
i-Filter™, Chemi-Block, UF Filter, UV e-boiling,
Mineral Charge Cartridge
5
Standard Filtration
Supplied
1
1
Power Rating
20 Watts (Max.)
1
Input Iron (Max.)
0.3 mg/L
2
Total Dissolved Solids
(TDS) (max.)
Up to 200 mg/L
5
Input Water
Temperature
10°C to 40°C
6
Input Chlorine Content
(Max.)
0.2 mg/L
3
Input Water Turbidity
(Max.)
5 NTU
4
Input Water Pressure
Range**
0.3 to 2.0 kg/cm
2
1
UV Lamp
11 Watts
3
UV Lamp Life
8,000 burning hours (as per manufacturer's spec.)
4
Operating Voltage Range
150VAC to 250 VAC, 50 Hz
5
Power Supply
Input 230VAC, 50Hz. Output: 12V.(ON Board AC -DC)
2
ELECTRICAL SPECIFICATIONS
RECOMMENDED INPUT WATER PARAMETERS
PRODUCT SPECIFICATION
*Technical Specifications are subject to change without prior notice.
Note: SMPS is designed to operate from 150VAC to 280VAC.
Note: The performance data presented in the table is applicable under standard laboratory conditions
#
.
Actual performance may vary depending on the input water quality, water pressure and condition of
filters. Input water quality/pressure/TDS are important determinants of recovery rate and rejection.
**If the input water pressure is more than 2.0 kg/cm
2
, installation of a PRV (Pressure Reducing Valve)
is mandatory. If the input water pressure is less than 0.3 kg/cm
2
, installation of a booster pump is
recommended. These accessories are available at an extra cost.
Warranty void if not installed as per recommendations.
#
Standard Test Conditions:
Feed Water Quality: TDS Max: 200 mg/L
Pressure: 1 kg/cm
2
, Turbidity: 1 NTU (Max.), Temperature: 25°C, Chlorine: below 0.2 mg/L,
Iron: below 0.3 mg/L, Life: 6,000 liters
Power
Parameters
LED Indication UV+UF
Remarks
All LEDs
Red, Green, and Blue will glow one after other for 1 sec.
Blue LED will be Solid if Power is Available.
Purification Process
Power
Service
Tank Full
Blue LED will be solid.
Red LED will Be OFF.
Green LED Will blink at 0.5 secs rate for 30 secs.
Blue LED will be solid.
Red LED will be OFF.
Green LED will blink at 0.5 secs rate continuously.
Blue LED Will be solid.
Red LED will be OFF.
Green LED will be solid.
Blue LED will be Solid.
Red LED will be Solid.
Green LED will be OFF.
Blue LED will be Solid.
Red LED will Blink at 0.5 secs Rate.
Green LED will be OFF.
Blue LED will blink at 0.25 secs rate.
Red LED will be OFF.
Green LED will be OFF.
Tank Filling Mode
Storage (Tank Full)
UV Lamp Error
SV Error
LPS
Power
Service
Tank Full
Power
Service
Tank Full
Power
Service
Tank Full
Power
Service
Tank Full
Power
Service
Tank Full
HERE’S HOW YOUR AQUAGUARD
®
NEO RO WORKS
PURIFICATION PROCESS IN YOUR
AQUAGUARD
®
NEO RO
HERE’S HOW YOUR AQUAGUARD
®
RO WORKS
Reduces TDS, hardness, pesticides and heavy metals like
arsenic, lead and mercury. Eliminates microorganisms like
bacteria, viruses, protozoa and cysts.
i-Filter™
Multi-Layered
Polypropylene Roving
Wound Cartridge
Chemi-Block
(with built-in
Particle Trap
Filter™)
Dust Free
Bacteriostatic
Activated Carbon
Block
Removes fine suspended particles such as dust, dirt,
mud and sand from water.
Reduces excess chlorine, bad odour, colour and
organic impurities. It also removes very fine turbidity
causing particles.
Membrane
Life Enhancer***
Special anti-scalant
media
Prevents scaling of dissolved salts on the surface of
the membrane, thereby, enhancing the membrane life
and performance.
Thin Film composite
(TFC) reverse
osmosis membrane
Reverse
Osmosis
Cartridge
Instantly charges purified water with essential
micronutrients like Calcium & Magnesium which
enhance the taste of water & makes it healthier for
consumption.
Mineral Charge
Cartridge
1.
2.
3.
4.
5.
Calcium & Magnesium
Enriched Water
Aquaguard
®
Neo RO
Model
2
Dimension (W X D X H)
320 mm x 278 mm x 476 mm
Net Weight
6.2 KG (Approx.)
3
Purification Technology
RO
6.2 Litres (approx.)
4
Tank Capacity
i-Filter™, Chemi-Block, Reverse Osmosis Membrane,
Mineral charge cartridge.
5
Standard Filtration
supplied
1
1
Power Rating
35 Watts (Max.)
1
Input Iron (Max.)
0.3 mg/L
2
Total Dissolved Solids
(TDS) (max.)
Up to 2,000 mg/L
5
Input Water
Temperature
10°C to 40°C
6
Total Hardness
600 mg/L
7
Input Chlorine Content
(Max.)
0.2 mg/L
3
Input Water Turbidity
(Max.)
5 NTU
4
Input Water Pressure
Range**
0.3 to 3 kg/cm
2
1
Operating Voltage Range
150VAC to 250 VAC
3
Power Supply
Input 230V AC, 50Hz./Output (internal AC/DC Adaptor)
24V DC, 2.5 A
2
ELECTRICAL SPECIFICATIONS
RECOMMENDED INPUT WATER PARAMETERS
PRODUCT SPECIFICATION
++
HYBRID DIVERTER
VALVE
NOTE : THIS IS A SCHEMATIC ILLUSTRATION OF THE PRODUCT TO GIVE A VISUAL SCHEME OF WORKING OF UNITS.
THIS IS NOT AN ACTUAL ENGINEERING DRAWING OF THE PRODUCT.
RAW WATER
INLET
SV-24V
BOOSTER PUMP
LPS
DRAIN
FLOW
RESTRICTOR
PURIFIED WATER
STORAGE TANK
FLOAT
DISC
MEMBRANE LIFE ENCHANCER
MINERAL CHARGE CARTRIDGE
RO MEMBRANE
I FILTER
CHEMI BLOCK
(WIT
H BUILT
-IN PART
ICLE T
RAP F
ILT
ER)
( WATER FLOW DIAGRAM )
AQUAGUARD Neo RO
Membrane life enhancer is
recommended to be installed
if the TDS is above 1000 ppm
or hardness above 300 ppm
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm
(mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost.
*Technical Specifications are subject to change without prior notice.
Note: SMPS is designed to operate from 150VAC to 280VAC.
Note: The performance data presented in the table is applicable under standard laboratory
conditions
#
. Actual performance may vary depending on the input water quality, water pressure,
turbidity and condition of filters. Input water quality/pressure/TDS are important determinants of
recovery rate and rejection.
**If the input water pressure is more than 3.0 kg/cm
2
, installation of a PRV (Pressure Reducing
Valve) is mandatory. If the input water pressure is less than 0.3 kg/cm
2
, installation of a booster
pump is recommended.
If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300
ppm (mg/L), use of a Membrane life enhancer is recommended.
These accessories are available at an extra cost.
Warranty void if not installed as per recommendations.
#
Standard Test Conditions:
Feed Water Quality: TDS Max: 1,000 mg/L with NaCl
Pressure: 1 kg/cm
2
, Turbidity: 1 NTU (Max.), Temperature: 25°C, Chlorine: below 0.2 mg/L,
Iron: below 0.3 mg/L Life: 6,000 liters, Pressure on membrane: 75 psi, Product recovery @ 25%
++
AQUAGUARD
®
NEO UV+UF
TECHNICAL SPECIFICATIONS*
